Jump to content
SAU Community

Jjr Dump Pipes

bnr034

By bnr034,
in Engines & Forced Induction

 Share

Recommended Posts

bnr034 Apprentice

bnr034

Posted
Posted

Right now i need a dump pipe to complete my exhaust system..

Are JJR dump pipe reliable... Anyone had any issues with theirs?? or should i save up for a jap one??

Are there much gain of gettin a full exhaust system??

Current exhaust system consist of

HKS hi Power Silent

de- cat

HPI front pipe

cheers

Link to comment
Share on other sites
Get EPIC Rising Star

Get EPIC

Posted
Posted
Right now i need a dump pipe to complete my exhaust system..

Are JJR dump pipe reliable... Anyone had any issues with theirs?? or should i save up for a jap one??

Are there much gain of gettin a full exhaust system??

Current exhaust system consist of

HKS hi Power Silent

de- cat

HPI front pipe

cheers

Ive had my jjr stainless bellmouth on 4 about a year now and no problems.Good upgrade over the stock item

Link to comment
Share on other sites
Mr. Untouchable Experienced

Mr. Untouchable

Posted
Posted

Just a quick note with the JJR dumps, I purchased a full "hyperflow" i think its called and few years back. $899, dump & front (ALL IN ONE) and cat back. looks great, nice cannon design And the angle it sits is bloody awesome, fitment was really good overall was very very pleased with the bang for buck. note this system has no mufflers.

Only last year I chopped my dump (wanted a bend for my new dump i was fabricating) and i noticed where the split/divorce pipe that separates the waste flap gas away from turbine gas flow merges back in around 50cm down, where they had made the whole for it to flow back into down the dump, its 40mm pipe and the bloody hole was oval, jagged and around 32mm in diameter.

now i dont suppose this is the end of the world, considering it was on a small low mount setup. but i did have some creep issues. it would always go a few extra psi. i was at the track once and tried to set it to 12 psi but after the run the gauge recall said i had hit 16-17.

but the rest off the system is very good. sounds great fitted very well.

so just be aware if you buy a split dump

cheers

Link to comment
Share on other sites
adamskill Mentor

adamskill

Posted
Posted (edited)

i have the bell mouth front/dump pipe on my 32gtst. i noticed a slight increase in torque. i had to cut the flange off and shorten the pipe by about 200mm then weld the flange back on, so just remember u may need to do the same thing. just a hot tip, spend 50bucks and heat wrap the pipe before you fit it. adam

Edited by adamskill
Link to comment
Share on other sites
Kinks Grand Master

Kinks

Posted
Posted

I bought a bellmouth dump and was quite impressed with the quality. I went away from the split dump after hearing too many stories of wastegate creep caused by the split flange fouling on the wastegate and preventing it from opening properly. JJR have probably fixed that by now but I couldn't see the need for a split dump on a street car.

Link to comment
Share on other sites
illusiVe Proficient

illusiVe

Posted
Posted

when you guys are talkin about it fowling the waste gate

do you mean

THIS ONE:

jjrscreamrb.jpg

OR THIS ONE:

jjrrbdump.jpg

OR THIS ONE:

jjrsplitdumprb.jpg

Cause im after just a split dump pipe so i can get some better exhaust flowage. (or all) and for my power range i dont think i need a full 3" removing the wastegate gasses from the stock 2.5" piping should free up enough flow as im only finding loss in power just before redline, however still sustaining maximum torque ;)

Link to comment
Share on other sites
ClutchBurndout-:( Grand Master

ClutchBurndout-:(

Posted
Posted

oh this is where my question comes, I ordered from jjr a front pipe dump pipe 1 piece, this dosent have the spliter at the start of the dump pipe for the other outlet on the turbo, is this a problem? Why do some dumps have the splitter to separate the 2 outlets? what difference is it not having the splitter? will i have problems at just 12 pounds stock turbo setup?

Link to comment
Share on other sites
DRD-00F Grand Master

DRD-00F

Posted
Posted

I have this: (didn't use those gaskets though)

jjrrbdump.jpg

Bought it probably a year or so ago? Haven't had any problems with it so far... Though the wastegate return was a bit rough on the inside, if I had something handy I would have cleaned it up...

Link to comment
Share on other sites
debonaire Enthusiast

debonaire

Posted
Posted

I have a JJR split front+dump ( the 3rd pic ), which I bought second hand.

Only issue I had was that the wastegate pipe, due to sticking out further towards the engine than a traditional bell mouth would, clashed a bit with.... something, I can't remember - I think the water line from the turbo. But it was no biggie - you just have to push it a bit.

In terms of bolting up to the turbo and cat, I had no problems. Well, I snapped half the bolts onto the turbo cause they were seized and its an absolute bitch to bolt back up (especially without ratcheting spanners) but no problem with the product :P

Link to comment
Share on other sites
bryno Collaborator

bryno

Posted
Posted (edited)

Isn't that the whole point of the bellmouth? The fact that it doesn't separate the gases like the split dump does?

On my GT-RS turbo the exhaust umm.. part that bolts to the dump pipe had a built in separator whereas the stock turbo didn't, so the separator attachment on my split dump had to be removed when the new turbo went on. Hope that made sense.. So I imagine you would need a separator attachment made up for your dump pipe if you actually want to make use of the split design.

Edited by bryno
Link to comment
Share on other sites
bryno Collaborator

bryno

Posted
Posted (edited)

was covered in great detail in a thread I read a while back.. something about turbulence and using a split dump to allow the gases to merge further down the pipe to create less turbulence/better flow.. think bellmouth allows you to go higher boost as the waste gate size isn't restricted like it is in the split design..

Some one who actually knows about this stuff would be better at answering that question though..

edit: found a bit of info on the split design.. gives you a bit of an idea, may not be entirely accurate though..

"Dual pipe technology is recognised by the major turbo company engineers to be the best way to make internally gated turbo's work in a most efficient way by breaking up (seperating) the different pressure ratio's between turbo and waste gas in order to eliminate turbulence. Eliminating all turbulance allows the turbo gas to rapidly accelerate away from the turbo. This action in turn reduces spool up time - produces more torque faster and will give a fatter torque curve all through the rev range."

Edited by bryno
Link to comment
Share on other sites
_Ryan_ Grand Master

_Ryan_

Posted
Posted
Ok but wat is used for what? Like if 1 big pipe is best why do they make split pipes? Or vice versa?

Do some searching, at higher levels of gas flow most splits have proven to be a restriction, and also a large number of wastegate flaps foul on the seperaters.... i would reccomend saving changing at some point, and getting a bellmouth, you could probably sell your HPI front pipe for the price of a JJR stainless bellmouth :blink:

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • TurboTapin
      R32 GTST - 600KW+ RB28/CD009 Build

      By TurboTapin · Posted

      So I've been working on the car a fair bit, doing a lot of little things. Preparing some projects for this winter, as I'm taking 13 weeks off very soon for parental leave. Have my second kid on the way and he's due any week now. I'll need something to do while he's sleeping. I also usually take the car off the road in about a month and a half, until sometime around the end of March.  Still making slight adjustments to my tune, as the cold weather settles in. I've also had to start dropping boost and tire pressure as the weather gets cooler. It's getting very swirly at highway speeds. I drop to 20psi at 20C and 18psi spring pressure at 10C IAT's. I'm currently on 255 Falcon RT660's, but may look into running 275's next summer. They will fit, but barely. Might have to raise the rear a tad.  I'll start redoing my exhaust Monday, as I have the week off. I currently have an oval center muffler and cannon rear muffler. I've been told more then once from people behind me that my rear bumper is going to catch on fire one day. Seems I blow 5-10 second flames after doing a pull. No clue if that's the WMI, as I've never been able to do that before with other cars. I wanted to angle my tip down a tad so flames are pointed down and away from bumper. I also wanted to take the opportunity to reconfigure my exhaust line. I'm going to move my oval muffler to the rear with a pie cut angled tip and put in a new smaller round muffler in the center. I've rocked cannon mufflers on this car for the last few years and want to transition back the oval muffler look. I've also been looking for a stainless project to try out the new solar flux I bought. I'll post pictures on Monday, should be able to wrap that up in a day.  I'm also picking up another rear subframe this week. I wanted a second so that I could modify one with a gk tech anti squat reduction kit during the winter, and still be able to keep the car a roller so I can back it out of the garage if needed. I will also be caging it this winter. More on that later. Lastly, Speedtek still hasn't given me diddly squat. Every week for the last 4 weeks, they have been saying next week. They told me Friday to expect a shipping label that day to ship my two bad sets of ring and pinions back and nothing. There's definitely been more contact since I started destroying their company any chance I get on Facebook, but it's still just words without action.   
    • TurboTapin
      Idle issue rb20det

      By TurboTapin · Posted

      Have you done a pressure test on your intake/piping? Cleaned your IACV and Cold start valve?
    • r32-25t
      Spotted on the street....

      By r32-25t · Posted

      Bit of a dump of ones I saw on my trip. I also have a heap from daikoko but that’s technically not  on the street 
    • HYBRID VL
      KISLOC2 line output convertor for subwoofer in Q50/V37

      By HYBRID VL · Posted

      i was thinking that the 2 wires that go to the sub from factory has some sort of preamp like you mentioned and also a lo Pass filter to get just bass. now that will only use 1 channel and that really should be all i need for a sub? if i was trying to put a set of speakers in the back i can understand cutting into the left and right speaker wires. i will try how im talking about doing it and if that is crap i will do it the way of all wires. thanks for the input guys.  
    • Equilibrise
      M35 Stagea intake suction pipe

      By Equilibrise · Posted

      Challenging mig welding thin Aluminium pipe and trying to fit it in, having to bend and twist, but got there in the end. Fits really well and can easily get a socket wrench in there now to put it on/off. I'm in the middle of another project, so haven't installed the suction pipe yet. I'll post some pictures and results when i do.
×
×
  • Create New...