Jump to content
SAU Community

Recommended Posts

i suppose it would depend what size tyres they are

if you have the normal 16" then somewhere between 32-34psi would be fine.

32psi is actually a mechanics tale..

its a "one size fits all" kinda beleif...

alof tires require more and some less...

always look at the side of the door..... where the latch is...

for stock tires and rims, that should be the exact size of tyre and pressure.

You know its actually spelt "tyre"?

lol

no its not

Tire is American english

Tyre is Uk & Australia

Just like Grey is spelt Gray... Aluminium is spelt Aluminum...Kerb is spelt Curb... Mould is spelt Mold & aeroplane is airplane. :P

32psi is actually a mechanics tale..

its a "one size fits all" kinda beleif...

alof tires require more and some less...

always look at the side of the door..... where the latch is...

for stock tires and rims, that should be the exact size of tyre and pressure.

32psi is not a mechanics tale... most mechanics will tell you to set your pressures to more like 36ish, depending on the car/tyre.

Don't necessarily follow the tyre placard as they are usually settings that achieve best comfort rather than best performance. (Although this isn't always the case)

I run my pressures (stock 17" rims) at 40psi. The best thing to do is monitor the way the tyre is wearing. If the outside edges are wearing more rapidly than the centre, your pressures are too low, and vice versa. Keep in mind there are other factors that can influence tyre wear though, such as wheel alignment, driver, etc...

32psi is not a mechanics tale... most mechanics will tell you to set your pressures to more like 36ish, depending on the car/tyre.

Don't necessarily follow the tyre placard as they are usually settings that achieve best comfort rather than best performance. (Although this isn't always the case)

I run my pressures (stock 17" rims) at 40psi. The best thing to do is monitor the way the tyre is wearing. If the outside edges are wearing more rapidly than the centre, your pressures are too low, and vice versa. Keep in mind there are other factors that can influence tyre wear though, such as wheel alignment, driver, etc...

well personally i prefer higher...

higher pressures give slightly better fuel economy than one being lacking pressure.

Beleive me, ive worked at 3 car dealership service workshops during my apprentice ship years ago.. and that was like the universal one size fits all tale.

like i said, it depeneds on the tyre and the load

the tyres on my Toyota Hilux i pump it to 55Psi cause anything lower than that, it looks flat...

well personally i prefer higher...

higher pressures give slightly better fuel economy than one being lacking pressure.

Beleive me, ive worked at 3 car dealership service workshops during my apprentice ship years ago.. and that was like the universal one size fits all tale.

like i said, it depeneds on the tyre and the load

the tyres on my Toyota Hilux i pump it to 55Psi cause anything lower than that, it looks flat...

Geez, that would be rough as guts. You obviously never go off road with it then.

i guess its up to the owner at the end of the day then really. when ever i have had new tyres put on the cars ive owned they generally get pumped up to 32-34ish. but from what ive read from other people today afew are running at 40+. just have a look on the side wall of the tyre and see if it has recommended psi and go with it.

well personally i prefer higher...

higher pressures give slightly better fuel economy than one being lacking pressure.

Beleive me, ive worked at 3 car dealership service workshops during my apprentice ship years ago.. and that was like the universal one size fits all tale.

like i said, it depeneds on the tyre and the load

the tyres on my Toyota Hilux i pump it to 55Psi cause anything lower than that, it looks flat...

Well I wasn't just rambling either...I worked at 2 dealerships during my apprenticeship and then for a general workshop after that. And never did anyone I work with tell a customer to put 32psi into a sports car tyre.

Anyway, I'm also sure your hilux is probably running light commercials, not road car tyres. I also put 50+ psi into those kind of tyres, but wouldn't recommend it to OH RB for his skyline...

And I wouldn't class my tyres as 'lacking pressure'. They are wearing fine and the car uses about 11L/100km.

So in the end, don't put 55psi into ur skyline tyres lol. If it were mine they would be up around 40, and monitor it from there.

lol

no its not

Tire is American english

Tyre is Uk & Australia

Just like Grey is spelt Gray... Aluminium is spelt Aluminum...Kerb is spelt Curb... Mould is spelt Mold & aeroplane is airplane. :D

LOL

The tyre pressure is more controlled by the tyre itself. Check the manufacture's tech data for the recommended pressure.

Most manufacturers (car and tyre) recommend a pressure that will aid in the comfort of the ride, ie they are a bit soft. Add at least 2 psi all round, then add another 2 psi to the fronts.

Well I wasn't just rambling either...I worked at 2 dealerships during my apprenticeship and then for a general workshop after that. And never did anyone I work with tell a customer to put 32psi into a sports car tyre.

Anyway, I'm also sure your hilux is probably running light commercials, not road car tyres. I also put 50+ psi into those kind of tyres, but wouldn't recommend it to OH RB for his skyline...

And I wouldn't class my tyres as 'lacking pressure'. They are wearing fine and the car uses about 11L/100km.

So in the end, don't put 55psi into ur skyline tyres lol. If it were mine they would be up around 40, and monitor it from there.

and where did i state to pump 55psi into his skyline?!

i told him to check the pressure at the tag on the side of the door trim...

it should have the exact pressure and size of the tires....

my car runs on stock wheels.

I wonder if the front and rear got different figures? as I've seen the figures for other cars tire pressure and the fronts figures are always different from the rears.

You would see this mainly on track cars where individual tyre pressure's are essential for cornering, e.g. more psi in the back = more over steer, less on the front = more grip but more body roll and understeer..... its a fine line!

I usually run 35psi on my 18's and find that its a good balance between tyre wall stiffness and grip.

Hope this helps you....

and where did i state to pump 55psi into his skyline?!

i told him to check the pressure at the tag on the side of the door trim...

it should have the exact pressure and size of the tires....

I never said you did :(

I just didn't want him to be confused.

  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I've run most of the semis which are available and sadly you can pretty much rank them by price.  Fast and spendy = Z221, A050, DZ03G Ok and mid range price = R888, V70A, A052 I don't really rate the AR-1 because it's not cheap enough for the performance level offered. Yes, they're much cheaper than A050 but V70A can be had just as cheap and is a much faster and more predictable tyre.
    • There's no current law that stipulates that you cannot eat dessert with a soup spoon, although, it is socially unacceptable of course, shame on you But, there are emissions laws, which is sort of on topic to the OP's questions Things like emissions are, if anything, going to get stricter in the future for road registered cars I believe, 'Merica has yearly emisions testing in some states, the UK has it's yearly MOT testing as well which includes emissions Building, and purchasing modified vehicles may become alot more problematic if you want to keep them registered, how, if, and when each state handles this is anyone's guess  More food for thought really
    • I'm on the AD09, strictly on the street. They are a very nice tyre, have done ~16k km and are near the end, might make it to 20. They are, in my opinion, very much just a street tyre. I wouldn't expect them to be equivalent to some of the others in your list on the track. Although I'd be pleasantly willing to be surprised. My memory of the AD08Rs is vague enough, due to the passage of time, that I shouldn't try to compare them, but I feel as if the AD09 is not quite as "sporty" as the AD08R was.
    • There's a difference between "selling" a product to someone (which, if you walked into a workshop or bricks and mortar store and bought and walked out with it, is just the act of buying and selling) and rolling your buggy into a workshop and having them fit non-roadworthy stuff to the car. And for the latter, let's ignore any potential legal loophole arguments that the armchair lawyer might want to make to differentiate between supplying your own parts to be fit by the workshop or getting the shop to supply and fit. The workshops that have been dealt with in the US for this are in the latter category. It would be near impossible to try to charge/attack/criminalise a shop for selling "for off road use only" parts to someone unless those things were intrinsically illegal in their own right, or had other legislation wrapped around them, such as there is for guns, pharmaceuticals, etc. Well, no. And you knew your argument was silly when you made it. And there is. it might be somewhat harder in Vic, but then that's the price you pay for electing the long list of (unts that you have to run the whole shit hole**. But otherwise, you can put an aftermarket or otherwise tunable ECU into a car and get it run through the whole shebang of emissions testing as part of an engineering cert and, so long as the tune is "locked" afterwards, then that modification is on the list that is approved on the cert. But....it is an expensive process. ** Of course, the (unts who make up a large proportion of the population that eternally try to get around the rules are also a part of the problem and the reason that you end up with draconian rules in the first place. By contrast, SA was founded and the government and civil service set up and run by very sensible types (largely German) who set up good structures that enabled a lighter touch of government on the somewhat better behaved population. it is only more recently that we have followed the rest of Australia down the criminal drainhole of penal colony behaviour and now we have to catch up with mobile phone cameras and so on.  
    • Not specifically the revamp Toyos. In the past I've used Nitto NT01s, which were essentially the same compound as R888 with a different pattern (that's what the internetz said, so just be facts). I did like the NT01, progressive fade, didn't go from grip to 0 grip in a split second. If you look at the serious street/track guys, most are either on Cup 2, A052, A050, AD09, CR-S or AR-1.  
×
×
  • Create New...