Jump to content
SAU Community

Recommended Posts

some cars have them stock, and some dont...

millions of people run without one, and i have NEVER heard of a turbo dying because of a no BOV situation...

you'll be fine deano...

  • Replies 53
  • Created
  • Last Reply

Top Posters In This Topic

Ok, here's the thing:

Compressor surge (commonly known as dose) is bad for your turbo. There is no real dispute about this. Whats in dispute is how bad it actually is, ie the simile mentioned before was a tennis ball against a brick wall.

What you got to remember is that if any given turbo has a life of 120K kms then compressor surge isn't gonna do you any favours in regards to life expectancy. From my experiences so far compressor surge is not going to have any affect (other than increased lag b/w gears) in the short term, but if ur looking to keep ur car for a few years and/or have an old turbo on there, I would def be putting on a BOV.

P.S., Ive got a blitz one for sale if u need it :)

how about a bov wound down fairly tight? tight enough to clearly hear compressor surge. when there is enough pressure, it releases back into recirc, but otherwise it doesnt.

thats how mine is, and i dont see any fuel economy issues, or added lag between changes.

a bit off topic, but still in the ballpark :)

Edited by Munkyb0y

This is what Corky Bell has to say about it. But with a name like that, i'm not sure what to believe :blink:

Compressor surge is the rapid fluctuation of turbine speed caused by the throttle's being closed under boost. Rapidly spinning air compressors (turbos) can go unstable briefly when this occurs. The fluctuating speed can be damaging to the turbo and the accompanying noise is obnoxious. The condition can be alleviated with a compressor bypass valve that opens as the throttle closes and allows air exiting the turbo to vent back to the front This keeps the flow up. Many modern turbo cars are equipped with such valving, but seldom are they big enough to handle high-flow, high-boost systems, A useful fringe benefit to these valves is that they reduce lag and perceptibly increase fuel economy.
Compressor surge is the rapid fluctuation of turbine speed caused by the throttle's being closed under boost. Rapidly spinning air compressors (turbos) can go unstable briefly when this occurs. The fluctuating speed can be damaging to the turbo and the accompanying noise is obnoxious. The condition can be alleviated with a compressor bypass valve that opens as the throttle closes and allows air exiting the turbo to vent back to the front This keeps the flow up. Many modern turbo cars are equipped with such valving, but seldom are they big enough to handle high-flow, high-boost systems, A useful fringe benefit to these valves is that they reduce lag and perceptibly increase fuel economy.

Obnoxious my ass!!

Edited by PM-R33

My mate put a turbo on a MX5 BOV'less and it lasted about 5 months before the shaft play was quite bad. No shaft play to begin with.

He has another one of the exact same turbo (he baught my old turbos, R34 standards) and is running it with a BOV and it is fine and has lasted already longer then the last one. In that mind that does it for me.

Running a AFM setup Nissan style, likely to hurt economy if anything. Certainly wont help it

Hmm i guess it depends on the car. Running no bov or an atmo bov should have the same effect on fuel economy. I run an atmo bov and still manage about 480km to a tank before the fuel light comes on. (Standard ECU)

My thoughts: Red top RB20DET + FMIC never had a BOV factory, wound it up to 14psi ran it for 3+ years pulled the turbo off and it was exactly the same as you'd expect a 120,000km turbo to be. A little bit of oil but nothing out of the ordinary, it still boosted hard. Car drove great. Put an R33 turbo on and continued running with no BOV, zero problems.

RB25DET S2, blocked the BOV off and the car ran like shit (I still have the factory SMIC). I think the newer ECUs are far more sensitive with their mapping and the airflow changes upset it.

I would have no qualms whatsoever running without a BOV, providing the ECU could handle it.

there is always shaft play.

Did a turbo swap on a mate's RB25, the brand new HKS we put on had about 3x the shaft play of his stock item. Excessive shaft play is a problem, minimal is not.

blades are spinning at several thousend rpm, them coming to a complete stop when air is pushed back through? it has 2 do sumthing

No. Do you think compressor wheels are made of paper mache? They have to be strong enough to compress air while being hot and spinning at a hundred thousand RPM. Do you think a little bit of chuffing noise is going to upset them? Doubt it.

What you got to remember is that if any given turbo has a life of 120K kms then compressor surge isn't gonna do you any favours in regards to life expectancy.

Most turbos last longer than that, but say 120k with a BOV and 115k or 110k without. Who cares?

My mate put a turbo on a MX5 BOV'less and it lasted about 5 months before the shaft play was quite bad. No shaft play to begin with.

Too many variables, or just bad luck. He was probably more careful with the second turbo as well.

Hmm i guess it depends on the car. Running no bov or an atmo bov should have the same effect on fuel economy. I run an atmo bov and still manage about 480km to a tank before the fuel light comes on. (Standard ECU)

logically speaking it wont have the same effect...

but every car/driver is different... i said it wouldnt help. :)

Here's a simple test.

First, obtain a tennis ball in the opposite hand that you throw with.

Subsequently, go outside your house, find a nice spacious brick wall, and through it at the wall.

Then, inspect the wall to see if there is any damage...

Same principle applies to air hitting the turbo fins.... :):ph34r:

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • My idle is set at 950rpm though - Moving the timing around 20 degrees is not really what I'd call a calm idle. That said... neither is chop, by definition. The LS ECU likes to adjust timing to hold idle as opposed to air. It'd work, but generally speaking there'd be a discrepancy in the base idle and the IACV would want to move the timing around anyway to maintain said idle. I think I'm just going to keep the timing steady anyway. Preserve my engine mounts.  My aircon is now officially regassed. As the guy was reversing I noticed my reverse lights do not operate, along with my reverse cam. This is a bit distressing, because 100% of guides talk about which wire to connect to backup cams as "the goes with the [other color] wire". Often when doing conversions. Unfortunately the R34 colour wires aren't documented Unfortunately I had a T56 Magnum gearbox with it's reverse switch, which also isn't documented. Unfortunately there's definitely not documentation for people with both of these in the one car. Unfortunately I forgot. After many hours of this, I have a reverse cam and reverse lights again. The wire going through the trans tunnel to the reverse switch had broken. Upon inspection, it looks like this one wire had about 7 spade terminals and extensions in it.. for reasons I cannot possibly comprehend. I also spent the 750 hours required to clean up the wiring behind my head unit which now looks like this: This is a monumental improvement relative to what used to be there WRT triple gauges, head unit, traction control, wideband controller, and whatever the f**k OEM stuff still exists there in various states of connectivity/needed. Next step is to check in at the Exhaust shop to see/confirm how much clearance I have, to decide what mid mufflers or 'resonators' (which are just straight through, narrower mufflers) I can add and hopefully cut out a lot of exhaust leaks, pinhole, v-band or otherwise. But first step will be to 'take a look' before the next step.
    • Fark the AFM card and Nistune, Haltech Nexus S3, DBW, cruise control, flex fuel, dis dat.  
    • It's most likely the bolt/bush where the cover bolts back wore and allowed cover to move forward.
    • Still haven't put the injectors and R35 AFM in so we can tune the bloody thing for the HG highflow it got mid last year! I think I can forecast the upgrade path to a bigger twin scroll, external gate, Haltech, flex setup, Samsonas, dis dat, etc will be .... a while away!
    • Should have taken that opportunity to slot in a twin scroll turbo setup. Maybe next time.
×
×
  • Create New...