Jump to content
SAU Community

Recommended Posts

Ok. My skyline has 60k on the clock and its a 95 yea sif thats genuine.

austats says that av car in Japan does 10k per year.

So my car would have done (on av) 80k.

My clock has been wound back and has stopped + there is a knocking sound under the dash wheneva i start but goes away within 3 secs. Could the 2 be related?

Final question I have a sticker right at front of my rb25det with 100,000 km on it and some jap writing. Is this saying yes we changed the timing belt at 100k or that the owner needs to change the belt at 100k.

My concillation is the int, mech and ext are all good and motor runs nice. Hoping that at least because that sticker looks new that the timing belt change was recent.

Or does that sticker just advise the owner to change it at 100k (hope so).

Can anybody with that sticker confirm or deny???

Link to comment
https://www.sau.com.au/forums/topic/26672-r33-imports-and-winding-back-odos/
Share on other sites

Where's the exact location of that sticker again, might check mine aswell.

But km less then 10km a year av, could also mean that they don't drive it that often right? Mayb just city driving?

Anyway where's the sticker located, under the hood i presumme and on what?

Cheers

p.s. You can also tell how much a car had been driven, by lookin at the interior, i.e seats, carpets, how faded things look etc.

the sticker is siting on the black plastic right at the front of the engine near the belts facing skyward...

Interestingly enough my interior is great (still has a new car smell - that totally spins me out).

Engine is clean and original and exterior is 95% spot on...

Gear shift and steering wheel both have a little wear (looks like owner didint know how to look after leather) but nothing excessive.

Pedals are worn but not much really probably 90% tread left on clutch pedal.

Just wish i had some way of really knowing for my own peace of mind and to keep tabs on the timing belt issue etc

My Silvia came in with 60,000 on the odometer.. it was wound back because every time the car reaches 69,999 it rolls back over to 60,000 again.

It doesnt bother me because i've had the car for almost two years and it was in excellent condition when i bought it and i've had absolutely no major problems with the car.

I know the sticker you mean. I have it too and from what I've been told, it is just a reminder to change your timing belt at 100ks. But, (as a freind told me a week ago), seeing most cars are wound back, alot of people change the belt straight away to be on the safe side, cause if it breaks, you are stuffed ! Well, going on his advice, I still haven't changed mine either..hehe (slack arse) But yeah, pretty sure that's what it is.

So not that is has been changed, but a reminder to change it when you reach 100ks...

I wouldn't be to sure on that.

When you buy a new Timing Belt that little silver sticker comes with it. If someone has written kms in pen on that little sticker, that's when your timing belt was changed.

The only reminder the mechanic needs to change your timing belt is when your car gets near to 100,000kms.

So your timing belt has been changed at some stage.

Another little indicator is sometimes they put the kms on the battery when it has been replaced and the date. Check on that also, could give you an indication.

yea read that in another forum bout the battery might take it out tommorrow (I did check while it was connected with a mirror but should have a proper look).

The writing on the sticker is actually typing and is the same as the jap writing ie the sticker wasnt written on thats how it was originally.

But now im thinking that even though the sticker is only a reminder that doesnt mean the car hasnt done more than 100k does it.. unless they rip it off during the service

Guess I'll just have to rely on the cond of the car the evidence is a bit sketchy (unless the battery tells a story). Bastards i noticed another sticker on the inside of the bonnect something to do with radiator cleaning/coolant it showed approx 60k but the date had the year purposely ripped off...

imho just about all cars are wound back ... so they can get that little bit of extra money cause a car looses quite a bit once it gets past 100k ... i wouldnt' be surprised if 95% of cars coming in are wound back ... it doesn't really matter theres nothing u can do about it ... just look after it right thats all .. i'm pretty sure the previous owner of my car is an old man because i found these sunnies in there LOL interior was ok ... i'm sure the car had done about 90kk when i got it it was 40k

Final question I have a sticker right at front of my rb25det with 100,000 km on it and some jap writing. Is this saying yes we changed the timing belt at 100k or that the owner needs to change the belt at 100k.

if this is the sticker you are talking about i still agree with what i said before :P

The sticker in the pic is a reminder to change the belt at 100,000Ks. think about it ....if you've wound it back to 60,000 you would hardly leave a polite little note saying you changed the belt at 100,000 would you.

Sensible thing to do with all imports is to change the timing belt AND the waterpump asop and start off fresh.

Yeah it's just a reminder, I picked my R33 up with 32K documented kilometers and it has the sticker.

BTW I only put an average of 5K on my car a year, most cars around the Tokyo/Yokohama area don't really see a lot of kilometers since most people use the trains to get around(cheaper and faster plus parking sucks). So some of the low kilometer Skylines running around are actually genuine.

one thing i noticed when looking for my r33 for about 8 months was that most skylines' had digits on the odometers that were out of alignment...this to me was a sure sign that someone tampered with the clock readings...out of dozens of r33's i looked at only 3 had 'aligned digits' on the clock as well as almost no wear on interior parts like pedals, handbrake, gear stick, seats, carpet etc. etc.

interestingly these 3 were all privately imported by people who went to japan to buy their skylines...

i am the proud owner of one of the 3, test done on the car prior to purchase also claimed km's were genuine, the engine is very quiet at idle i.e no bearing noises, gearbox is very good also.

the car had 50+ kms; after two years and as driven daily now has 90+ and never missed a beat.

car also came with a lot of paperwork such as auction documents, cancellation of rego in Japan etc., and seem to support the odometer reading.

but there is always a small doubt in my mind.......

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • So we have most the interior back in, and for the first time with one OEM speaker hooked up. The 31 is running, driving and now tunes!!! Hahaha yet another step for the sub that sat 10m under for two weeks!!! unbelievable really 👌 lots of love work and not giving up on her. Seen so many youngsters part way less, and in way better condition. I’m stubborn, thinking another problem is just a hurdle to overcome, One at a time. IMG_9277.mov
    • That is correct. I'm using a modified ABS ring and a ZF speed sensor on my rear diff for speed input. I'm running a Haltech ecu. 
    • Been busy with the newborn. We originally thought we were going to go for a third, but we're good with two lol. He's starting to actually sleep now so I've had some energy to work on the car. It's been parked away in the garage since late November due to winter.  I went ahead and redid all my head oil drains. I originally had my front and rear head drain going into the same pipe but have since split them up. I also added an Ethanol content sensor to get ready to run E85 this summer. Tossed it on my return line. Sensor sits nicely under my intake manifold.    I also have a lot of parts that came in for my rear end. I'll be swapping over to a 3.3 final drive and doing the GK teck anti squat mod. While the rear subframe is off, I'll also change every bushing. We're planning on buying another house soon with the condition that I get at a minimum a 2 door garage, so I'll wait to have more room for this. Now onto the strange things that recently happened... After changing the lower rad hose (It had been sitting in my cabinet for well over a year and was the last hose I had to replace), I let the car idle in the garage to bleed my coolant. After running for a few minutes, it started missing. Got much worst within a minute or two and then stalled and would not restart. My crank sensor decided to crap itself. No damage, no explanation, just died. I went ahead and replaced it with another ZF sensor but the heavier duty stainless model with a shield. Tossed that in and started right up. Has anyone else seen this? I hate when things fail without cause. Luckily this was a blessing in disguise... This lead me to recheck my timing. It seems I may have had a beer or two the last time I had set my TDC angle as I was off exactly 5 degrees... I miscounted a line haha. I was running 5 degrees less then commanded. It's a little embarrassing but helps explain why my dyno operator seemed to think I should be making more then 478rwkws.        
    • Sharing results from recent Liberty Walk R35 GTR, since they are still considered as somesort of a V36 Skyline. We do them turbos too. This are high flowed SS-1 models with ball bearing conversion done.  Car have managed to pull 485awkws @ 20Psi so far pushing limitations of factory built engine. The build list for R35 GTR enthusiasts as follow : HyperGear high flowed stock turbos in SS1 (G25-660 specs) Custom titanium intake pipes. Vspec performance titanium front pipes. Vspec performance 4" titanium exhaust. Upgrade fuel pumps. 1200cc injectors. Ignition coilpacks Hks intake plenum. Hks intercooler piping. Greddy intercooler. Greddy bovs. Top-secret coolant reservoir. Emtron ecu. Straight E85. Built gear box.  
    • Nah no bearings, just slip fit.  Would be a reasonably challenging but not impossible job to modify it to run bearings but I'm hoping that's not necessary as I may have well built one myself if I end up spending hours modifying it!
×
×
  • Create New...