Jump to content
SAU Community

Recommended Posts

pushead - I took off all my intake piping which was suprisingly clean, and gave it a bit more of a clean.

I then cleaned my afm and then took off the thottle body and cleaned that. Out of the lot the throttle body looked the worse (thin layer of very thick oil around it).

After putting it all back i found a noticible difference in throttle response and felt like it came on boost a bit smoother.

It will only cost u 1 bottle of carby cleaner. Would be interesting to see before and afters on a dyno of doing this.

  • Replies 80
  • Created
  • Last Reply

Top Posters In This Topic

yes it does... it always does... no matter what mods, tyre pressure, clutches all come into play.... put a decent clutch in a stock car and u will probably chop almost half a second off the time.

I made 140rwkw at BMT.

Mods:

* 3"dump/front

* 3" cat back (crappy cat is still the bottleneck)

* Bleed valve set at 0.7 bar (~10psi)

* K&N Panel filter in stock air box.

* Pineapples (prolly wont affect a power reading)

I couldnt give a rats ass what rwkw I've got. I ran a 13.83 @ 101mph last weekend which is similar to others with 180+rwkw.

nigasnt is 100% correct, rwkw dont mean squat!

thanks for all your input ppl. I was wondering ok, instead of measuring in rwkw but 1/4 mile times, did anyone measured their 0-100km/s? if so what results? reason why i asked is most street drags are 0-100km times, please also note i do not encourage anyone to street drag, but im sure we all have done it some stage :P:)

i think bmt dyno is lower (someones already prolly said what im saying b ut i cbf reading the whole thread)

so is racepace's dyno, best way to find out is either test on anotehr dyno or simply ask the guys at BMT if that's the average power they have seen on cars with your mods, they'd know best :P

This dyno is way low for sure!!

RiggaP said he ran a 13.8 or something with a dyno result of 141rwkw... For your car to run high 13's you have to be pushing about 180rwkw plus..

I had my r31 dynoed at Goodguys in bayswater and got 160rwkw @ 12psi and I know my car is probably good for low to mid 14's..

Take it to the track, see what sorta MPH you get

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • I have a 6 boost manifold and it has loads of bends etc. turbo has a cover however manifold doesn’t so I started to wrap what I could without taking turbo off. Very restricted area   are you stating wrapping could lead to cracking weld? Is that because heat is retained?    i have a exhaust gas temp right after turbo and it hits 700degree or 800 at times.   there are areas which is impossible to reach with fibre glass cloth. Is there anything I could apply such as the photo shared earlier which would formulate around exhaust pipe in difficult to reach areas, sort of like aluminium foil flexible to shape it in place?   i think from earlier reply you mentioned acl? Is this what you meant?   https://www.nstparts.com/product/acl-heat-shield-700x275     photo of my engine bay   https://ibb.co/9grHsMN https://ibb.co/bXC8KRM https://ibb.co/KV3kGZc   I am trying to cover bottom of the exhaust manifold which joins the turbo. Only way is to take turbo and possible manifold out as it also touches the engine mount which I don’t fancy doing
    • So....I managed to fix the belt coming off problem, but unfortunately i destroyed my oil pump. While testing and hitting my rev limiter a bunch, my oil pump took a shit. I actually heard it break. In my great wisdom i decided to hit redline 5 times (original plan). Lowered it to 7500 for the soft limiter. Normally it would come off on the first go. The 6th time I hit the limiter the pump broke and as i began accelerating again and hit it the 7th time, oil pressure dropped and the protection kicked in. It actually made a "tink" as if i dropped something hollow.   The motor is pulled and should be rebuilt and put back in 3 weeks. No bearings were spun and i could have gotten away with simply replacing the pump, but since i had to pull the motor....might as well build it   I made a billet tensioner and the belt stayed on without getting frayed. I also made one for a friends R33, but I was thinking of using a hydraulic unit to keep constant pressure on it when the belt stretches.
    • Yeah 98 for me, and 6.7/100 was my actual usage. On the downside the bloody thing still isn't running properly but at least they hybrid system is happy now. It starts but missfires like a bastard, and isn't throwing any code except "missfire". Thanks scoop. I did notice the AFMs are reading quite different at idle 1.33v and 1.67v so 25% variance (and have both changed and swapped them, the issue stays on the driver's side afm) so I'm looking for exhaust restriction (mouse nest?), compression issue or (hopefully not, no physical damage seen) wiring issue. Throttle might also be an issue but that is harder because you can't swap them side to side and not cheap to fire the parts cannon at.
    • I hope you're right and it somehow justifies it's existence!
×
×
  • Create New...