Jump to content
SAU Community

R33 Gts-t Randomly Stalling While Driving? Pls Help!

Turbz RB-25

By Turbz RB-25,
in Engines & Forced Induction

 Share

Recommended Posts

Turbz RB-25 Experienced

Turbz RB-25

Posted
Posted

Hi Fellas,

My car has started to stall randomly while driving and while idleing.

For example, I would be driving my car 10-15 mins, and then it feel like the engine shuts down, then switches back on, the shuts down, switches back on, almost as though the fuel cuts in and out.??

The happens can happen whenever, full throttle, idle, cruising speed, you name it.

It'll happen to me 2-3 times while driving and frankly it's getting quite dangerous when my car stalls on a busy street.

WHen the problem occurs on idle, the rpm drops to almost 0, then bounce back up to 1000, then back down to almost 0, so strange? and it only occurs some times which really puzzles me?

SOmetimes I can go for a 30min drive and it doesn't happen...

DO you fellas have any idea what it might be?

Fuel pump? Coil packs? spark issue? Tune on the car?

ANy help would be great.

Cheers and have a good long w/e

Benzino33 Experienced

Benzino33

Posted
Posted
Hi Fellas,

My car has started to stall randomly while driving and while idleing.

For example, I would be driving my car 10-15 mins, and then it feel like the engine shuts down, then switches back on, the shuts down, switches back on, almost as though the fuel cuts in and out.??

The happens can happen whenever, full throttle, idle, cruising speed, you name it.

It'll happen to me 2-3 times while driving and frankly it's getting quite dangerous when my car stalls on a busy street.

WHen the problem occurs on idle, the rpm drops to almost 0, then bounce back up to 1000, then back down to almost 0, so strange? and it only occurs some times which really puzzles me?

SOmetimes I can go for a 30min drive and it doesn't happen...

DO you fellas have any idea what it might be?

Fuel pump? Coil packs? spark issue? Tune on the car?

ANy help would be great.

Cheers and have a good long w/e

That happened to my 33, I replaced the Idle stepper motor, cleaned the AFM and repositioned the TPS. fixed it.

Good luck

Turbz RB-25 Experienced

Turbz RB-25

Posted
  • Author
Posted

CHeers Fellas, will get some carby cleaner tomorrow.

By the way, is it ok if I use degreaser instead of carby cleaner?

The reason I ask is because I got degreaser at home but no carby cleaner. Cheers fellas.

smok74 Community Regular

smok74

Posted
Posted
Hi Fellas,

My car has started to stall randomly while driving and while idleing.

For example, I would be driving my car 10-15 mins, and then it feel like the engine shuts down, then switches back on, the shuts down, switches back on, almost as though the fuel cuts in and out.??

The happens can happen whenever, full throttle, idle, cruising speed, you name it.

It'll happen to me 2-3 times while driving and frankly it's getting quite dangerous when my car stalls on a busy street.

WHen the problem occurs on idle, the rpm drops to almost 0, then bounce back up to 1000, then back down to almost 0, so strange? and it only occurs some times which really puzzles me?

SOmetimes I can go for a 30min drive and it doesn't happen...

DO you fellas have any idea what it might be?

Fuel pump? Coil packs? spark issue? Tune on the car?

ANy help would be great.

Cheers and have a good long w/e

The less residue you leave on the AFM the better - residue (especially oily crap) promotes more sh*t sticking to the wire element .... what I did with mine, flushed the element in the middle of the AFM with a bit of acetone using a little squiter / dropper.... watched all the brown shit come dripping off. Just gotta watch the acetone doesnt come into contact with the wall of the AFM for too long, being plastic, you wouldnt wanna melt it lol its lucky acetone evaporates quickly....

Turbz RB-25 Experienced

Turbz RB-25

Posted
  • Author
Posted

Hi fellas,

I got some carby cleaner yesterday and cleaned the wires in the AFM with it.

Alot of brown shit flowed off so it looks brand spankin new now.

It hasn't stalled since and I have a feeling the problem is solved (fingers crossed)

Thanks for all your help fellas, greatly appreciated.

Turbz RB-25 Experienced

Turbz RB-25

Posted
  • Author
Posted

Fellas,

The stalling thing happened again yesterday...... I must say but it's improved,

If it was a 8/10 pain in the arse last time, now it's about 2/10.

Nonetheless, it's still doing it??

Should I take out the AFM again and spray it again??

Beelzebub89 Grand Master

Beelzebub89

Posted
Posted

Is your BOV plumb back or atmo? Atmo vented BOVs have been known to cause the same problem. Could also be your Idle Air Control Valve? I think its called. Will probably need cleaning and the idle resetting eiter with the TPS or through the ECU.

When I had my 33 gtst the same thing happened to me. I did the above and it never happened again.

Here is a great tutorial for cleaning the IAC in case you're unsure what to do.

http://www.skylinesaustralia.com/forums/Di...nd-t110431.html

Turbz RB-25 Experienced

Turbz RB-25

Posted
  • Author
Posted
Is your BOV plumb back or atmo? Atmo vented BOVs have been known to cause the same problem. Could also be your Idle Air Control Valve? I think its called. Will probably need cleaning and the idle resetting eiter with the TPS or through the ECU.

When I had my 33 gtst the same thing happened to me. I did the above and it never happened again.

Here is a great tutorial for cleaning the IAC in case you're unsure what to do.

http://www.skylinesaustralia.com/forums/Di...nd-t110431.html

Yeah, I might give the ACC a clean.

It's strange, when idle drops, the voltage on the PFC displays 8.8v, maybe it's something to do with my alternator?

Turbz RB-25 Experienced

Turbz RB-25

Posted
  • Author
Posted

What puzzles me is that it can happen at any time, thats why I don't think it's the ACC. The stall can happen even when I am fully on boost, and bang it'll just cut out, then it will cut back in again... It can also randomly just happen on idle...

Maybe it's something to do with the tune???

Turbz RB-25 Experienced

Turbz RB-25

Posted
  • Author
Posted

I've narrowed it down to the following things:

1) Crank Angle Sensor

2) Fuel Pump

3) Harnesses to sensors

4) Ignition Control Module

5) 02 Sensor

6) Coil Packs

7) Spark Plugs

8) AFM

What do you fellas think?

Turbz RB-25 Experienced

Turbz RB-25

Posted
  • Author
Posted
series 1? sounds like the classic power transistor/ignition module is on its way out

It's a series 1, but it has a series 2 engine?

I've also recently placed the RB30 short block on it, with 256 in 264 exh cams, porged pistons, rods etc etc, and a GT35R turbo.

The car is currently on it's run in tune.

sometimes in the middle of driving the engine just stalls... it can usually be just pulled over onto the side of the road and started again.. sometimes it doesnt quite get to the point of stalling but just has an extreme lack of power and no acceleration ability for a few seconds..

I've read a few commodore threads and it seems that their problem is always the CAS...???

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • MBS206
      Rb26/30 build

      By MBS206 · Posted

      And if you want more power, more reliably, and cheaper, go get the Aussie RB... The 4L Barra and put that in instead.
    • MBS206
      Nismo rear spats

      By MBS206 · Posted

      No cats will keep discolouring the rear bar. Sends white paint a weird yellow stain. Cut and polish normally gets it out, but you'll be doing that every fortnight I found.
    • Butters
      Rb26/30 build

      By Butters · Posted

      Both heads will be equally reliable or unreliable depending on what you do to them.  Stock the RB26 head will flow more. You have access to the stock intake ITB manifold on the RB26 cheaply which flows really well(1000hp+).   Arguably more aftermarket support for RB26, though in Aus we love our RB30 SOHC heads too.    The only downsides to the RB26 head is if you have a VL commodore and want to keep the SOHC look.  Where you may have an issue is drilling out the rb30 block for the bigger head studs but if you are building a big power motor you'd probably put bigger studs on the SOHC head too.  This is just about finding a good machine shop, sometimes easier said than done.  RB30 head worked can make big power just like a Rb26 head, so really it actually more comes down to what your preference is for your car.  People now even making billet versions of both.
    • GTSBoy
      Rb26/30 build

      By GTSBoy · Posted

      2630s work perfectly well. There is something to be said for just using the 30 head, as it saves all the pain of the conversion, still makes tons of power, still sounds cool, etc etc. 2630 will obviously make more power again, but the differences are not stupidly big. It really depends on whether you're racing for sheep stations or not. If it's dead serious, then it's a 26 head. If it's just for fun, it could go either way. But the 26 head and the effort to get it set up, etc etc, is part of the fun.
    • lilley's gtr
      Rb26/30 build

      By lilley's gtr · Posted

      I've been building a 26/30 for a few years now. I've had the head built with all the good stuff. I had a 32 gtr but blew it up and yes its all going into a vl but im looking for some advice from some RB nuts on pros and cons on putting a 26 head on a 30 bottom end is it worth it Works are as follows Head -Extensive porting 1mm oversized supertech valves Supertech double springs Supertech valve guides Supertech titanium retainers Tomei solid lifters Tomei 270 x 10.25 cams Head drain Bottom end series 2 rb30 block Cp ceramic coated pistons Eagle rods Romac balancer Oil restrictions  O ringed blah blah spent a fortune And will get a girdle because the 30s arent used to handling that much rpm Nitto billet oil pump Hypertune plenum 6boost mani Refurbed astra pump thats the cover for it in the boot I did have a precision 6262 but sold it because drag car life. Currently building the ass end full 4 link floater rear end with a 2 speed  But the dilemma i have is my mate rekens I should just stick with the 30 head for reliability. Has any one had any issues with mounting the 26 head ie compression blowing gaskets etc. Just looking for some advice from people who have gone down this route. Here's some photos. Blew the oil pump in the gtr and decided to rip the motor out at the time and do a full build only to find it had been a repairable write off so went down this path.     
×
×
  • Create New...