Jump to content
SAU Community

Recommended Posts

Ok people its time to let my good friend go as i need a upgrade for work purposes (unfortunately)

1996 R33 GTS-t White Manual 122,000 kms.

Car has been serviced reg every 5,000 kms and i have been the only owner in Aust since the car was imported in 2005.

car has the follows mods

HKS Coilovers (adjustable)

HKS High Flow panel filter

Front Mount Intercooler (custom piping back through Std holes, ie not cutting)

Sparco Racing 17'' 235 front 255 rear

Bose Importing Split Dump/front pipe

Catco High Flow Cat

Blitz Nur Spec Cat Back

Exedy Sports Organic Clutch

Greddy Profec B spec 2 Boost controller (car runs 11 psi)

Apexi SAFC 2

Alpine Head unit (inc direct i-pod connection)

Alpine splits and 6x9

Cadence 4 way Amp

other parts that are not on the car : - Std turbo back, Side mount intercooler, Blitz BOV and M's pod filter.

Car is very clean, only blemishes are small tear on drivers bolster and the front spoiler is cracked (it can easily be repaired or taken off and it just bolts over the std spoiler)

$11,900 ono

any questions you can get me on 0412464683 or just pm me.

post-24776-1240824742_thumb.jpg

post-24776-1240824801_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/267342-r33-gts-t-series-2-melb/
Share on other sites

PRICE DROP $10,500 ONO

THIS IS CHEAP PEOPLE CAR HAS SOME QUALITY MILD MODS ON HER!!

VERY REWARDING CAR TO DRIVE ESP ON WINDING ROADS :(

ONLY REASON WHY I'M SELLING IS BECAUSE I'M GETTING PRESSURE FROM WORK TO UPGRADE!!

  • 2 weeks later...
  • 3 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Unfortunately haven’t taken pics yet after it was finished. All the edges are hemmed nicely, just had to cut holes for the gear shifter and seat bolts and seat belt bolts in the rear. The molds seem like they’re done with steam and a layer of glue on the underside to hold a bit of shape but still soft enough that it’s a good fit when it’s all pressed down.
    • When's the rear mounted turbo kit coming? Needs dose and V8 chop idle lol.
    • I was very unimpressed with how the car came up from the A pillar forward, before I hit things (twice). It all has to go. It had to go, but now it has to go... more. So we finally found the very first Shennanigans with the entirely perfectly setup engine that had no problems being pulled apart to improve on 'was perfectly fine'. Cam bearings looked a bit... stock. Which isn't entirely bad given they were stock and this is a ~20 year old engine. So new cam bearings are on the way because it's somewhat difficult to get to this stage to do it later, and it will trash the block. It was quite unusual that it wasn't done when the perfectly new-looking VCM cam was originally installed by [unknown] What IS unusual is the cam that was installed there was advanced SIX degrees. As to why there is no way to know.. however it could have been @Dose Pipe Sutututu's mate who wanted a larger cam sound but also wanted it to come on earlier to be more usable. This is my dyno sheet with the previous setup - This cam is not supposed to peak until 7000+ RPM, according to VCM. This is what lead me down the whole 'my heads/intake setup is running out of puff and can't support the cam' line of thinking to begin with. Anyway too late now - New cam is in! It could be rather funny if this smaller cam acts like a larger cam because it isn't advanced six degrees. In the spirit of everything is working amazingly - the COMP cam required no dialling in whatsoever. It was about 0.5 degrees advanced, which seems pretty bang on. Any adjustment either way would be further out. I'm told as a chain breaks in it ends up regarding back about 0.5 a degree as the chain breaks in, making it bang on. In the spirit of everything was previously working amazingly - The timing gear that was taken out turned out to be was an N-Motion double timing chain kit, with adjustable cam gear (which is how it was 6 degrees advanced) and all looks entirely perfectly new. It also had a Torrington bearing, which was one of the reasons I ended up getting the Cloyes kit which they used in the C5R 24 hour racecar - Because I couldn't confirm what was in the engine when talking to Tony Mamo. I did believe however it was a Double chain kit of some kind... but found no supporting documentation or evidence for it.
    • I recently did this to my R33 with the full set from Car Mats Direct, they can't do the vinyl anymore that's advertised on the website due to a supplier issue so I ended up with the Black Loop Pile which looks great. I went all out with rubber sound deadening sheets from Repco and also added the sound deadening foam layer option with the carpet. Makes a world of difference and got rid of all the weird smells in the 29 year old interior. It was a bit of work but I'd 100% recommend it, Car Mats Direct had awesome customer service and quick postage. Replaced my seats with some sporty ones from Autotechnia while I was at it, feels like a new car.
×
×
  • Create New...