Jump to content
SAU Community

Selling R33 Std Coilvers/pillow Tops, Flywheel, Coilpacks And More

R33_Rob

By R33_Rob,
in Classifieds

 Share

Recommended Posts

R33_Rob Proficient

R33_Rob

Posted
Posted

Hi guys,

Selling the following:

Standard R33 GTST S2 flywheel. Was removed at 112XXXkm.

$100.00 neg

Standard R33 GTST S2 coilpacks. Removed at 117XXXkm

$40 each neg

SuperSpark Coilpacks for S2 R33 GTST. Brand new never used, payed $400 will take $250 neg

Standard R33 GTST S2 Suspension. Remove at 117XXXkm

$110 neg each or I can remove the pillow tops if you need them for another setup. Note, one of the rear shocks has absolutely shit itself and in its current state is a hazard to drive with.

Apexi Pod Filter

$40 neg

Items located in Bulimba, Brisbane (5KM south of CBD)

Contact me on my mobile: 0408 783 953

Link to comment
Share on other sites
  • 1 month later...
 Share
Go to topic listing


  • Latest Posts

    • RB25inside
      Compatible rear drive shafts R34 N/A?

      By RB25inside · Posted

      Are these the Dmax ones you are in reference too? https://justjap.com/collections/driveshafts-bearings/products/d-max-reinforced-replacement-rear-driveshaft-set-fits-nissan-s13-s14-s15-r32-r33-r34-c35#description Not a bad idea to get the uni flange ones. I have sent just jap an email too. Will see what they say lmao. Only thing is the Dmax ones are on a big back order. Low key anything will be better then my OEM ones I got as they are sounding like popcorn when I go under load lmao 😂☠️🪦.
    • GTSBoy
      Compatible rear drive shafts R34 N/A?

      By GTSBoy · Posted

      They should do. I have S14 (or something S chassis, anyway) driveshafts in my R32 (because my diff flanges have 3x2). They're the right length. When you go looking for R32/3/4 driveshafts (for turbos), they're all the same thing, so are the same length. So there really shouldn't be any reason why those cheapies from JJ won't also fit an R34. R32/3 NA should also be the same thing. The (3x the price) D-Max ones are uni-fit. They have 5x1 and 3x2 bolt holes and say they cover all the cars. So that would also suggest that they are all the same except for the flanges. And in that case, the flange goes both ways. I'd be buying the D-Max ones if I ever have to replace a shaft. Because that will open up diff options without needing to juggle shafts also. Juggling shafts is gay.
    • ChoppedSpots
      GReddy Injector Help!

      By ChoppedSpots · Posted

      Yeah with the adaptors they do look like the photo above - just the fitment within the plenum itself and then further with the rail to the intake is questionable - we shall see tomorrow hopefully once I get some replies from Aeroflow, maybe those bosses are the missing piece....
    • Dose Pipe Sutututu
      GReddy Injector Help!

      By Dose Pipe Sutututu · Posted

      Should be fine, if you have it sitting too far in, you end up just spraying the walls and have shit idle. You "can" run them like that, however I don't think it's a great idea (also depends on your plenum, might be good to just get the injector bosses first, mock it up and see if you need to get the bottom extension) Ideally your injectors, with the extension should look like this  (Not my photos, just Google)
    • ChoppedSpots
      GReddy Injector Help!

      By ChoppedSpots · Posted

      Thanks for the replies guys, it's really appreciated.  It seems the kit was supposed to come with those injector bosses but hasn't. Unsure if they'll help as even with the adaptors to make them a 3/4 height injector they still sit too far out so mount the fuel rail?
×
×
  • Create New...