Jump to content
SAU Community

Recommended Posts

dose any one have tips getting an hcr32gtst past epa

convered all back to standerd

excepet spit fire coils

10psi actuator

3inc cat back

frount mount and piping

no bov

standard ecu( insted of mines ecu)

standard fule press reg ( insted of sard ajustable )

still with walbro 440 fule pump

standard injectors

new plugs

new oil 0w40 castrol edge

standard turbo & manafold (insted of t51 high mount)

standard air box mounted on angle due to intercooler piping(removing washer bottel to fit)

NEED HELP

wont pass on idle

DBs ok got down to 89db

ARGGG

dont know what else to do

Link to comment
https://www.sau.com.au/forums/topic/268734-need-help/
Share on other sites

dose any one have tips getting an hcr32gtst past epa

convered all back to standerd

excepet spit fire coils

10psi actuator

3inc cat back

frount mount and piping

no bov

standard ecu( insted of mines ecu)

standard fule press reg ( insted of sard ajustable )

still with walbro 440 fule pump

standard injectors

new plugs

new oil 0w40 castrol edge

standard turbo & manafold (insted of t51 high mount)

standard air box mounted on angle due to intercooler piping(removing washer bottel to fit)

NEED HELP

wont pass on idle

DBs ok got down to 89db

ARGGG

dont know what else to do

A guy i know got busted for his zorst being too loud he put a plate with a smaller hole between the flange on the cat it passed

Link to comment
https://www.sau.com.au/forums/topic/268734-need-help/#findComment-4580419
Share on other sites

  • 1 month later...
A guy i know got busted for his zorst being too loud he put a plate with a smaller hole between the flange on the cat it passed

exhaust is now fine

still wont pass!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!

disconced varex canon did the trick

and yes it now has an adr aproved cat

all before i went for the test!!!!!!!!!!!!!!!!!!!!!!!!!

dose any one have a clue!!!!!!!!!!

Edited by Rits2.0tpig
Link to comment
https://www.sau.com.au/forums/topic/268734-need-help/#findComment-4645770
Share on other sites

Haha I'll let you know RE the exhaust, girlfriend just got an EPA notice for her Datto ute being too loud, will probably try drilled out bits of metal between flanges since it apparently already has 2 mufflers :S. I have had a flange put after the last bend of my pipe so I can swap over a cannon if need be.

Link to comment
https://www.sau.com.au/forums/topic/268734-need-help/#findComment-4646251
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • As a general rule removing rubber fuel hose is so difficult I would replace it if it hasn't been done in the last 5 years. The risk you damage the liner or one of the inner layers is pretty high if it's not almost brand new. BMW's recommendations around coolant hoses is similar. My R33's fuel hoses at the fuel tank were so perished that they were ready to burst FYI. 
    • Ah yep, will do. Cheers!
    • Yes. It's either "2 wires", or 1 wire, depending on how you look at it. It is the connection that ties the battery -ve to both the chassis and the engine. Every electron that goes in or out of the battery goes through those 2 small spots (on the inner guard and on the engine block). If those are not clean and tight, then shit starts to suffer. Yeah, but measure it again cold in the morning, after it has had hours to rest. You can't usefully test the charge state of a battery immediately after it has been running because the alternator puts a surface charge onto the plates that takes a while to soak in and balance out. It will always read higher, and potentially look properly healthy, when fresh off of charge. But hours later it can look a lot less healthy. It's also worth measuring the battery voltage while cranking, although this can be difficult with a typical DMM because the screem update rate is so slow on most of them. An analogue voltmeter is actually a better tool for that. If the voltage drops too far while cranking, it is a sign of a poor battery. Although I don't think we're necessarily looking for a weak battery here - just wanting to exclude it.
    • https://www.facebook.com/share/15ZMn5oXtc/ Updated Event (so its not private and can be shared easier)  Attempting to coordinate a big push of Stagea's to this years GTR Festival. Great event last year and hoping for the same this year.  Discounted tickets 20% off for their various tickets until the 3rd of Feb Monday. Drags, show and shine etc.  I've emailed them to ask to set a location aside for the Stageas for the show and shine - they are happy to do so if we can get them numbers, I'm happy to keep track of that. Entering as Nismo category.  I'll be road tripping up from Melbourne, would be cool to convey if people are interested, maybe there is SAU convoys from each capital? If you have ideas about that let me know.  https://gtrfestival.com.au  
    • Does have series 2 airbag steering wheel and passenger side airbag also.
×
×
  • Create New...