Jump to content
SAU Community

Recommended Posts

  • Replies 44
  • Created
  • Last Reply

Top Posters In This Topic

There is a whole heap of shit I need,

Dash surround

L/R sunvisors

ashtray

l/h door trim (down the bottom with the skyline written on)

the inside of the boot e.t.c

CHeers

PM SENT

pm sent

i may be intersed in selling my 5 speed gear box an fly wheel an cluch an all so have i brand NEW ikeya formula sequential shifter never been used owns me $2,500 looking to see if there is any OFFERS out there can do a good deal on bost gear box/shifter box has done only 66,000kms still look new if i get the right money i will sell it all

hey all i am now selling my CHEETAH alarm which cums with tilt sensor,central door locking,interior movement sensor, an lots more cost me over $1200 for the alarm an all the accessories

asking $500.............

hey here is sum photos off the alarm thanks

post-59764-1245560880_thumb.jpg post-59764-1245561018_thumb.jpg

  • 2 weeks later...
hey still got sum bits left

Hey I've still got door trims, back seat, seat belts, all the mouldings around the seat belts, lots of switches and stuff out of the dash, airdconditioner, condensor, engine fan and shroud, full wiring loom from front to rear, spare wheel and lots of other little things. Need all this stuff gone as it is taking up too much room in the shed. Offer me anything - even a carton of beer as I just might consider it. Get yourself bargain today! If most stuff is not gone by the end of the month, it's going in the bin!!! Thanks

Hey I've still got door trims, back seat, seat belts, all the mouldings around the seat belts, lots of switches and stuff out of the dash, airdconditioner, condensor, engine fan and shroud, full wiring loom from front to rear, spare wheel and lots of other little things. Need all this stuff gone as it is taking up too much room in the shed. Offer me anything - even a carton of beer as I just might consider it. Get yourself bargain today! If most stuff is not gone by the end of the month, it's going in the bin!!! Thanks

cluster sun visors door strips kick panels door trim switches are all sold still got alot off parts in the shed thanks to all that have been helping me out buying stuff off me pm me if you need anythink thanks

Hi,

After the drivers side A-Pillar trim and trim piece under the steering wheel that has the cover for the fuse box (and some models the footwell light).

Both in dark grey colour (i assume all R33's the same).

Im in adelaide as well so hopefully can arrange pickup, as the a-pillar trim is a pain to send.

Cheers,

Kyle

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Does anyone know what the centreline should be for the vct intake cam? On my cam spec card it just says VARI and doesn’t actually tell me what the centreline should be. I had to adjust my exhaust cam gear by about 5 degrees advanced so I’m guessing I would have to adjust my intake as well? Current intake centreline is 119 deg. Iv already asked kelford and they won’t respond, It’s the 246-A 262 cams.  thanks for the help guys 
    • Get a timing light on it and verify it's sparking reliably at a sane ignition timing. Use a COP extension lead to be 100% sure about timing instead of hoping that the timing loop on the back of the engine is accurate. Make sure it's actually injecting fuel. MAF is not used on the stock ECUs for initial cranking.
    • RE5R01A is the transmission. Didn't realize they had a 5 speed for the NA cars but for some reason the turbo engines stuck to 4 speeds. Looks like the solenoid block is still available from Nissan directly at a somewhat reasonable price: 31940-60X01 https://www.amayama.com/en/genuine-catalogs/epc/nissan-japan/skyline/er33/6568-rb25de/trans/317 I would move sooner on this than later. The moment the de minimis exception for Japan goes away expect to be paying 25% tariffs even for stuff like this.
    • Only RB26 are low from factory. And even then the ECU actually want high impedance, because it's essentially the same ECU as the RB20 anyway, and thus they have a f**king resistor pack!
    • Is this preventable by priming the system with external oil pressure? I've seen the speed academy folks hook up an external oil priming system to the oil pressure sensor port with an air compressor to check for oil leaks before putting an engine back in a car. Something like this: https://www.jegs.com/i/JEGS/555/23550/10002/-1?gPromoCode=SPRINGINTOSPEED_APR25_5Off&gQT=1
×
×
  • Create New...