Jump to content
SAU Community

Recommended Posts

Hey ppl.

Happy new owner of a r34 manual 4 door with 70 000km.

So far have changed pads to bendix, oil change with 10-40w penrite fully synthetic and bosch filter.

Getting a power run Friday, wondering what it should make. I use mobile 8000.

With sump and filter they should take 5 litres of oil?

What oil pressure should they sit on (factory gauge)? Mine is just below 4 when driving. and bit over when boosting.

Also oil temp seem to be on 92 when fully warmed after 12 mins or so.

Are these figures normal?

Any noobie hints and tips with making the car last as a non thrashed daily?

Link to comment
https://www.sau.com.au/forums/topic/269820-new-34-owner/
Share on other sites

Hi Samuel,

Welcome to SAU... :whistling:

All the figures you've quoted are OK. Oil temp can go to 97 up a hill at throttle.

Cheers, T

Tips?

If your car is just outta Japan, I'd change all coolant fluid and get the Jap H2O outta there lest it affect radiator, heater core etc.

Check for spot rust on rails, damaged areas (that have been presumably fixed OK).

Change oil every 5000Km. Keep logs/receipts to maintain value of your car (if one day you sell it).

Detail ie clay bar/polish/wax your car if there's any acid rain damage from Nippon

If it's a genuine 70,000 Km with Jap logs, everything is sweet: but if there's no logs that you can trust, you might think about changing timing belt/water pump.

Link to comment
https://www.sau.com.au/forums/topic/269820-new-34-owner/#findComment-4592323
Share on other sites

Hey ppl.

Happy new owner of a r34 manual 4 door with 70 000km.

So far have changed pads to bendix, oil change with 10-40w penrite fully synthetic and bosch filter.

Getting a power run Friday, wondering what it should make. I use mobile 8000.

With sump and filter they should take 5 litres of oil?

What oil pressure should they sit on (factory gauge)? Mine is just below 4 when driving. and bit over when boosting.

Also oil temp seem to be on 92 when fully warmed after 12 mins or so.

Are these figures normal?

Any noobie hints and tips with making the car last as a non thrashed daily?

as per your technical questions:

* Oil capacity is 4.5L for Rb25DE and DET for oil + oil filter change...

* as for oil pressure.. according to workshop manual, it depends on your Revs.

For Rb25DE 2000Rpm is 3.3 and 6000rpm is 5.3

for Rb25det 2000rpm is 3.5 and 6000rpm is 5.6

so what your displaying sounds about right for regular driving.

ill get back to you on the exact Oil temperature, shortly....

Link to comment
https://www.sau.com.au/forums/topic/269820-new-34-owner/#findComment-4592375
Share on other sites

oil pressure sounds the same as mine. at first it is over 4 until the car gets to operating temps.

and as for the tips for keeping it in shape for a daily id say just service it regulary and only use the best fuel and it should be fine.

Link to comment
https://www.sau.com.au/forums/topic/269820-new-34-owner/#findComment-4592624
Share on other sites

oil pressure sounds the same as mine. at first it is over 4 until the car gets to operating temps.

and as for the tips for keeping it in shape for a daily id say just service it regulary and only use the best fuel and it should be fine.

Mine does exactly that, nice!!

Link to comment
https://www.sau.com.au/forums/topic/269820-new-34-owner/#findComment-4593196
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Any number of different ways. Have the coils draw sufficient current to provide contact wetting. Use different contacts in the switch, either by material or design, better suited to the low current drawn by a relay coil. Etc.
    • Hmm, how does the R34 manage to have headlight relays then without getting excessive carbon buildup on the headlight switch contacts?
    • Not R7R. Meant to type R&R, obviously enough.
    • Bugger "making it look stock". I put one conventional internally fused Hella relay behind each globe. I just pulled the plugs off the back of the globes and built new loom segments with male and female plug parts to match up to the original loom and the globe, and used the original power wires to each globe coming from the switch through the original loom plug to trigger the relays. Ran a big fat (also separately fused) power wire across the front of the car to feed all the relays. It's as ugly as f**k, but it is wedged down between the headlight and battery on the RHS and the airbox and headlight on the LHS, and no-one ever looks in my engine bay, and on the odd occasion that they do I simply give no f**ks for what they think. Fully reversible - not that you'd ever want to. For f**k's sake. It's a Skyline. They made million of the bloody things. We've been crashing them into roadside furniture for 30 years now. There is a negative side effect to putting relays on the headlights. The coil current is too little to properly clean the contacts in the switches and they get blacked up and you have to open them up every couple of years and clean them manually. I have 25 years of experience on this point.
    • I was poking through the R34 wiring diagrams vs R33 and noticed that the R34 has proper headlight relays while the R33 is like the R32 and sends full headlight power through the headlight switch. I'm not afraid of wiring but I really would like to do this in a way that looks OEM (clipping into open positions on the OEM relay box) and also unlike the factory wiring which interlocks the high beam and low beam on the halogen series 1 GTR headlights I want to make it such that turning on the high beams keeps the low beams on as well. Any advice on how to locate the specific connectors + crimp terminals + relays I need? I was thinking one NO relay for low beams and another for combined high + low running off the factory high beam headlight connector. I don't really want to splice into a crusty old probably discontinued factory harness so fully reversible is my goal here.
×
×
  • Create New...