Jump to content
SAU Community

Recommended Posts

This problems only been starting since i've relocated my amp for my splits to under the drivers seat.

Anyway, I start the car up, drive off, no worries no interference or whine through the speakers what so ever. Pull over, stop, turn the car off, go do whatever, come back say 10 minutes later and crank some tunes and theres now whine in the speakers.

Start the car a few hours later and the whine has since left.

Can anyone see a reason for why this problem only occurs when the car has been running, stopped and then started again???

Thanks

Tim

Link to comment
https://www.sau.com.au/forums/topic/26994-that-dreaded-speaker-whine/
Share on other sites

The whine is actually electrical interfierance being induced into your RCA cable. Move all of your RCA cables far away from any power cables.

Next step is too triple check all earths including the one from the head unit and all amps to ground and from the battery to the bodywork. Make sure they are clean and the paint is rubbed back where they bolt to the bodywork. Make sure they are screwed in tight also check that the insulation on the signal cables isn't worn / cracked / damaged. :rofl:

Have you checked your flux capacitors? or perhaps the warp power relays? .................. Sorry about that! My missus had the same problem in her lancer and it ended up being the amp itself.I moved it back to the original position and it made no difference. i then used the amp on low pass for the sub and the noise was gone, seems to be a filtering problem in the amp. try another amp

Well your fronts need a high pass so they play treble only and your sub/s need low pass for bass only, so if you are running seperate amps and they are hi/lo pass selectable try swapping them to see if the problem goes away. The amps are probably different power ratings but it is just a test so lower your gains. another problem can be that your gains on your amps are too high, you should set your gains as low as poss and your head unit volume to about 90%, as a rule of thumb. I know it can be time consuming but most car audio development is.If you just lower the frequency then you will miss out on high notes and it will sound dull. good luck

yea the fronts hav a high pass on them.

I run jaycar 6.5 inch carbon fibre woofers with JVC cross overs and tweeters on the dash. The amp i use for the splits is a Pioneer 4x50wrms amp (coupla models old now) but still does hte job well.

Gains are set at just on half and the frequency is set on high pass @ 70hertz or there abouts.

I could run the gains higher because im not pushin the limits of the woofers what so ever and they're very efficient.

Is it worth trying another amp to see if its a problem there?

My amps located under the front seat if anyones had any problems there before

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I mean yes, if you're starting from scratch on an unknown engine yes you don't need to be doing all kinds of math in the background but if you're doing relatively minor changes like AFM + injectors + boost up with some aftermarket turbos it takes quite a bit of math if you want to do something like maintain OEM fuel + timing tables but compressed and then a bit more load scale up top. I think I've spent too much time working on big engineering nightmares though so I'm a big fan of trying to constrain the scope of whatever work I'm doing as much as possible and trying to get it right before moving on. For example, a local owner just did the usual E85 + single turbo conversion to his R32 GTR and nearly burned his car to the ground doing some spirited driving up the local mountains. Turbine is unshielded and too close to the hood insulation. It's tough to balance "just get the project done" and "seemingly small details can cause massive setbacks I'm not willing to deal with".
    • No idea about Neil's steering wheel, but I have the same behaviour in the Stagea. I doubt it has ever been messed with so might be normal. Indicating to turn right at a roundabout and correcting even a little bit to the left to go around will cancel the indicator. Never considered it an issue other than it being a bit odd.
    • Does anyone know if this is off centered? Looks like it, when I indicate to go right, but turn my steering wheel slightly left it cancels (was always like that even before I started messing around with it) was wondering if anyone else has the same issue?
    • Nothing photo worthy since last update, lots of little plumbing bits for the AAC/Cold start valves, and unfortunately I still need another couple of parts for the brake booster line and the AAC into the plenum. Otherwise it all looks good to start up engine wise, onto checking the electrics/interior
    • Good news mate, plenty of spares available 5:40  
×
×
  • Create New...