Jump to content
SAU Community

Recommended Posts

  • 3 weeks later...
  • Replies 218
  • Created
  • Last Reply

Top Posters In This Topic

For those of you that have fitted these arms what bolts did you end up using? I tried the standard M12 bolt but the shank it too big for the arm ;)

Just the standard bolts are fine, there is a collar on both sides of the arm that slot in the bearing, they pop out, just run a drill through them quickly, its only off by .5mm or so, and its only on one of the bolts thats fatter after the thread.

Sweet. Will do that when I get back home again. Unfortunately I am missing the outer bolts as I already had the whiteline camber kit installed, no biggy will just get the same size as the inners.

  • 1 month later...
  • 2 weeks later...

RacePace installed the new UAS camber arms in the GTR this week and could only get 2.5 camber, even after cutting the bolt a bit!

Do you keep cutting the bolt into the thread to make it shorter to get more camber? Are there any other differences in the street and R track version or just keep cutting the bolt??

Im not real happy as i ordered the Race version and the ones i got did not have a R on them after asking RacePace. As I'm in Tassie and my first pair got lost in the mail and waited ages for the second pair and i had them sent strait to RacePace this time.

Any help will be much appreciated

Cheers, Ray

  • 5 weeks later...
  • 4 weeks later...
  • 4 weeks later...
  • 1 month later...

Hey guys, I organised the group buy at aus300 site and do alot of web based stuff with UAS.

Spoke to JP today he has sets of arms currently in stock, I think it was thirteen sets. I doubt there will be another group buy on these so if you want a pair grab them while they're in stock.

You can contact UAS on 02 9620 9000 or email [email protected]

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Well, hydraulic lifters will get noisy if they are dirty/fouled in some way, and exactly how that manifests will depend on exactly what schmutz is where. There is a procedure on here somewhere for dismantling and soaking/cleaning them. Replacing them with new is about 50% of the work and about 5% of the money!
    • Thanks for the reply @GTSBoy this is is a hydraulic lifter engine. Yea right i did not realise the lifters were supposed to be compressible while installed. I could push them down but i had to lean almost my while body weight on them.  I have never heard of a lifter/ lifters ticking only at hot idle and getting worse the hotter it gets. I have owned a few jdm cars with noisy lifters. This noise is slightly more subtle, it is more of a sharp gentle metalic tic than the solid and more loud tapping I've heard on lifters. I have used a metal rod, alloy tube, hose and stethoscope and could not find the source of the tick. But it appears to be loudest on the actual engine block behind the exhaust cam gear and next to the oil filter. I had mate (40 year old mechanic) go over it with me and he couldn't find it either..  Could it be a cam seal issue of some sort?  Cheers  
    • This seems problematic and unlikely at the same time. Vanilla RB2Xs have hydraulic lifters. They do have "zero" clearance, but only when running with oil pressure inside them. When not running, you should be able to compress them and obtain heaps of clearance. RB26s and Neos have solid lifters. They should have ~0.3mm and ~0.5mm on the inlet and exhaust respectively. If they have zero clearance then bad things are happening. With nothing else being wrong, it would mean that the valves would be held slightly (ever so slightly) open when they are supposed to be closed and it should have all sorts of problems when running, caused by leakage in/out through the valves. Or, zero clearance can indicate severe valve seat recession. None of it is good. Have you used a piece of hose as a stethoscope to try to localise the noise?  
    • Sorry for reviving an old post, but I'm having the same hot idle tick issue. Did anyone ever find out what it was?  I have checked/ replaced Injectors Coils checked Lifter clerance (is at zero) Checked Cam lobes Replaced exhaust gasket and studs Would appreciate any advice this is driving me nuts  
    • There's a huge reason manufacturers are tuning in dead flat torque curves... Make them reliable (and more drive able)
×
×
  • Create New...