Jump to content
SAU Community

Recommended Posts

Item: r32 89 gtr

Location: taree

Item Condition: tidy

Reason for Selling: time to move on to some thing else... maybe build some thing else....

Price and Payment Conditions: 20000 not a cent less or ill just keep her!

Extra Info: r32 gtr 1989 model

rebuilt motor about 10000kms ago

cp pistions rings

acl race series bearings

rev light weight rods

acl race series metal head gasket inlet gaskets

ported poished head matched manifolds

jun bronze valve guides

stainless steel valves

shaved head block ect

fully balanced bottom end crank etc

all new gaskets

new Garrett GT2860R5S 360Hp ball bearing turbos

new radiator

all new rubber hoses

Greddy hard pipe intercooler kit

K&N pod air filters

Sard 720cc injectors

Sard in-tank fuel pump

Re-wired fuel pump

Turbo Smart fuel pressure reg

Jun oil pump

Jun oil pump crank collar

Cam plate covers

Baffled sump

Oil restrictors in the block

Power FC computer with hand controller

E-boost 2

full 3 inch exhaust

Buzz adjustable suspension

Lowered springs

4wd/2wd switch (to make it into rear wheel drive or 4wd without getting out of car)

OS Geiken twin plate clutch

Lightened flywheel

336rwkw on 17 psi 455hp

car has ran a 12.0 181kmh on old stock turbos easy mid 11s car as is...

there would be more i have not thought of.....

no one will drive it until i see a deposit no time wasters!

also comes with 2 brand new 245s semi slicks have not been fitted...

gates race series timming belt new water pump just been serviced to all new fuilds box diff brakes every thing!

its still running a little rich atm 11s afr so its a safe tune! will go 500 at the wheels with a tune up and a bit more boost, makes 455hp on 17 18 psi

also new brake pads and skimmed the front disks new abs unit, pulls up as hard as it goes

pm me

post-42837-1242868370_thumb.jpg

post-42837-1242868391_thumb.jpg

post-42837-1242868412_thumb.jpg

post-42837-1242868429_thumb.jpg

post-42837-1242868445_thumb.jpg

post-42837-1242868462_thumb.jpg

post-42837-1242868494_thumb.jpg

post-42837-1242868516_thumb.jpg

post-42837-1242868530_thumb.jpg

post-42837-1242868546_thumb.jpg

post-42837-1242868564_thumb.jpg

post-42837-1242868575_thumb.jpg

post-42837-1242868587_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/271022-r32-gtr-455rwhp/
Share on other sites

Item: r32 89 gtr

Location: taree

Item Condition: tidy

Reason for Selling: time to move on to some thing else... maybe build some thing else....

Price and Payment Conditions: 20000 not a cent less or ill just keep her!

Can you give me a little more info on the 'Tidy' How is body, interior, tyres, paint (any dents/scraps) that sort of thing. Scouring the East Coast for a pearler of a 32 thats had the engine built internally. Much appreciated.

Link to comment
https://www.sau.com.au/forums/topic/271022-r32-gtr-455rwhp/#findComment-4610946
Share on other sites

paint is very good few little mark here and there odd tiny dint as you would expect for a 20 year old car..

alot cleaner than most of the ones i looked at when i bought it.

front tyres are cheap ones but 90% i will fit the semi slicks brand new 245s on the rear when i have a buyer rears are worn out done 30 000kms

scratches on front lip and rear bar is fading on a spot was quoted 400 to respray both bars and front lip

so thats why the price is 20 not 25 in side is very clean no rips or tears seat covers all ways on the front

and no one really ever goes in the back

Link to comment
https://www.sau.com.au/forums/topic/271022-r32-gtr-455rwhp/#findComment-4613755
Share on other sites

Guest Solman

hey got a few questions,

who rebuilt the motor for you, do you have receipts for this?

when you say "cp pistions rings", does this mean Cp pistons and CP rings, or just the rings? sorry just little confused about this.

the new radiator is it a standard R32 GTR one or after market.

How is the gearbox and diffs have they been serviced lately?

sorry about all the questions mate, i am really keen on a GTR and i am looking at getting one with a rebuilt/forged motor like yours.

thanks again

Edited by Solman
Link to comment
https://www.sau.com.au/forums/topic/271022-r32-gtr-455rwhp/#findComment-4620383
Share on other sites

hey got a few questions,

who rebuilt the motor for you, do you have receipts for this?

when you say "cp pistions rings", does this mean Cp pistons and CP rings, or just the rings? sorry just little confused about this.

the new radiator is it a standard R32 GTR one or after market.

How is the gearbox and diffs have they been serviced lately?

sorry about all the questions mate, i am really keen on a GTR and i am looking at getting one with a rebuilt/forged motor like yours.

thanks again

no worrys mate gpm local work shop all papers for the build, engine in out, turbos the lot all brand new parts!!! lots and lots of money spent on it!!!!

yes cp pistions and rings!

its a brand new stock radiator 500 bucks never gets hot but put a new one in any way to be safe and all new rubber hoses 550 bucks worth

gear box is fine diff has a slight wind has never got any worse.... both oils have been changed engine oil filter gets done every 3000km! and clean air filters

questions are fine mate any more just ask only reason i am selling is to build some thing differnt time for a change will be a VERY sad day tho if she dose sell :D

Link to comment
https://www.sau.com.au/forums/topic/271022-r32-gtr-455rwhp/#findComment-4622877
Share on other sites

really thought there would be more interest? :) i know you never get your money back but there could be over 20g spent on this!

i have my new project now so im ready to let her go

Link to comment
https://www.sau.com.au/forums/topic/271022-r32-gtr-455rwhp/#findComment-4626376
Share on other sites

  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • You're not wrong, but more than a few times I've heard of people running into issues where their injector characterization isn't quite right and that approach works for that specific configuration but once they switch over to a new set they discover a whole bunch of stuff wasn't set up correctly. It's slightly more annoying to reverse engineer the OEM MAF transfer function but you already have the sensor wired up to the factory harness so keeping it around for a few weeks more while you figure out the tune is easy enough. I've seen GM also use a combination of both MAF + MAP in their ECUs before, MAF is for steady state and a calculation of the cylinder VE to correct the base VE table, then in transients it uses that calculated VE + raw MAP to determine cylinder filling somehow.
    • I know this one’s the BB one. My tuner did make mention about the actuator. I am curious about the VCT as well
    • Might also needs a stronger actuator with the right preloading. With older 2019 built bush G3 units, BB upgrade or 21U housing down size makes a pretty decent gain in response as well. 
    • Hey lads  so im finally putting together my rb30 forged bottom end and ran into an issue. I measured my main bearing clearance with arp main studs torqued to 60 ft-lbs using ACL H series STD size bearings and standard, un-ground crank shaft journals and got an oil clearance reading of about 1.3 thou measuring straight up and down and about 2.8 thou measuring at a 45 degree angle (just above and below the parting line). My machine shop said they measured the main tunnel and it was all within spec (they didnt say the actual measurement) and to go with a standard size bearing, which i have done and the clearance is too tight, I'm guessing because of the extra clamping force from the arp studs distorting the main tunnel. I was wanting to run about 2.5 thou main bearing clearance.  My questions are: 1. could i just use the HX extra 1 thou clearance ACL bearings? that would fix my straight up and down clearance making it about 2.3 thou, but then would the side to side clearance be too big at around 3.8 thou? 2. what actually is the recommended main bearing clearance for measuring near the parting line / side to side. i know its supposed to be bigger as the bearing has some eccentricity built into it but how much more clearance should there be compared to the straight up and down measurement? at the moment there is about 1.5thou difference, is that acceptable or should it be less? 3. If i took the engine block + girdle back to the machine shop and got them to line bore the main tunnel (like i told them to do the first time, but they said it didnt need it) what bearing size would i buy? the STD size bearing shells already slide in fairly easily with no real resistance, some even falling out if i tip the girdle up-side-down. If im taking material out of the main tunnel would i need a bearing with extra material on the back side to make up for it? this is probably confusing af to read so if something doesn't make sense let me know and ill try explaining in a different way. My machine shop doesn't come back from christmas break until mid January, hence why i'm asking these questions here. TIA for any help or info 
    • I bought the model back in Japan in Feb. I realised I could never build it, looked around for people who could build it, turns out there's some very skilled people out there that will make copies of 1:1 cars or near enough. I'm not really a photo guy... but people were dragging me in a group chat for the choice of bumper as someone else saw the car before it was finished as they are also a customer of that shop. I took the photo in the above post because I was pretty confident that the lip would work wonders for it. Here's some more in-progress and almost-done pics. It gives a good enough idea as to what the rear looks like!   I have also booked in a track day at the end of January. Lets all hope that is nothing but pure fun and games. If it's not pure fun and games, well, I've already got half an engine spare in the cupboard 
×
×
  • Create New...