Jump to content
SAU Community

Recommended Posts

I have a problem with my car again its a R33 S2 and it is missfiring, I know this topic has been covered tons of times but I have fixed the missfire previously by buying new coilpacks. I bought JJR coilpacks and the missfire was gone for maybe 6 months, the car reved very smoothly all the way to redline... and now I'm getting a missfire at about 5000-5500rpm and up until then the car feels flat like it has no balls and then at about 6000rpm it feels like it takes off until redline.

Could this be that the coilpacks have fudged them selves?

Also I have replaced the spark plugs with iridium ones about 6 months ago just before i changed the coilpacks.

Any ideas? Could it be a injector?

Link to comment
https://www.sau.com.au/forums/topic/271189-missfiring-again/
Share on other sites

there is a sticky in general maintenance, they say to tape up your coils due to tiny cracks in them(electrical tape). Might be worth checking a very cheap option, at least the u can diagnose the problem this way.

+1

Worked for me

there is a sticky in general maintenance, they say to tape up your coils due to tiny cracks in them(electrical tape). Might be worth checking a very cheap option, at least the u can diagnose the problem this way.

I got new JJR coils, they shouldnt need to be taped...but i guess if it stops missfirring when they are taped then this just means they are arking out then they are fooked...

My plugs are gapped to the standard irridium plug size which is 12mm i think. But they shouldnt need to be gapped if i got new coil packs rite??? They should be strong enough to make the spark jump accross stock gapped spark plugs?

Edited by da spike

change the plugs to BCPR6ES gapped to .8mm then put a little mark in texta on the spark plug where the electrode is open (ie where you can see the most of it) when doing up your spark plugs point that mark to the inlet manifold you would be surprised how often this will fix your problems you want the mixture to be ignited if the electrode is facing the exhaust manifold it wont run as well small point but makes a big difference

I'm interested in seeing what happens. I have spitfire coils and gapped my plugs to 0.8mm as almost everyone recommends and it run absolutely crap after 4,000 rpm, gapped them to 1.1 and revs out to redline beautifully.

i installed my splitfires today along with new plugs gapped to 0.8mm, idle's fine but when i go to drive my car is missfires hardcore even at low revs...! rkn i should regap to atleased 1mm?

Another question... how do you guys gap the plugs without fooking them? Just tap them down with a small hammer?

I just gave it kinda firm knocks on my workbench and a feeler gauge to verify the gap - seemed to do the trick fine.

I'm just thinking could this be RnR? Because i would find it hard to believe that the coilpacks would have shit them selves after a few months use and i have changed the sparkies too when changing coilpacks to irridium ones... The missfire or popping under acceleration usually happens on a really cold night, the car also feels like it has a flat spot from 4500rpm to 6000rpm and then from 6 onwards its fine...

if it is happening more when it is cold then it may be rnr. but remember that the VCT turns off at 4500rpm so you do get a bit of a flat spot there.

to gap the plugs you need a feeler gauge. basically it is a set of small sheets of metal all different sizes.

i personally think iridium spark plugs are a waste of time. the set in my old 33 were shagged after about 20,000kms. i put the ones listed above in and changed them after 10,000kms and they were still fine. they are only a few dollars a plug.

as for there the tip of the plug is and marking it with a pen and trying to align it with the manifold, you may find that doesn't always work, without ending up with either it too loose or way too tight. however it shouldn't really make a difference as the valve will be closed well before the spark plug fires

Ok I got BCPR6ES plugs and threw them in and took the car for a spin just quickly and it looks like its not missfiring anymore... :D But I will need to drive it more to make sure because sometimes the missfire would be tempremental..

But what it's still doing is running shit from about 4500rpm all the way to 6000rpm and then it kicks in hard. Do you guys think this is rnr?

By the way I'm running standard boost and its going up to about 9-10psi cause its a cold night and exhaust, intercooler.

i personally think iridium spark plugs are a waste of time. the set in my old 33 were shagged after about 20,000kms. i put the ones listed above in and changed them after 10,000kms and they were still fine. they are only a few dollars a plug.

The iridium ones i took out (i put these in about 10,000 kms ago) were pretty fouled up so i guess copper ones are the cheaper alternative...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I have offset Nismo brackets so the fact the gktechs can pivot is less important to me. I have 170mm JIC arms with bushings - but they provide no adjustment and I'm not sure whiteline eccentric bushings will fit them (I don't want to ruin the bushings currently in them to find out). Ideally I want something with bushings + adjustment; hence why I'd like to find a pair of these. Unfortunately they aren't easy to find.
    • @Vee37 How much do you really care about finding these pads again? If your pads are quiet, work well and produce minimal dust, really isn't that enough? If you are set on finding the exact pads again, I suppose I'd do something like this -  Visit your local Jax, find out what brand of pads they carry. If the Jax workshop you previously went to had the pads on the shelf, then you can almost guarantee it will be of said brand.   I'm guessing you don't have the receipt for the previous work and pads. Can you visit a Jax workshop and see if they can look up your previous job to see what pads were fitted?  Still no luck? Put your stalker hat on, find the staff that used to work at the Jax store and ask them. Talk to local workshops, try to find out where the mechanics went to. Talk to Jax workshops, maybe they relocated to another workshop. When it comes to mechanics, its a small world. You'd be surprised how easy it is to track someone down. If these ideas don't work, shit will start getting crazy very quickly.... You could find out every brand and model of pad that fits that car... and try them individually ticking each off the list if it wasn't the one you were looking for.... If you go down this path your going to want to learn how to swap pads yourself, it is very easy, takes minimal tools and space. If you have room to park the car you have room to swap the pads. Plus you have the advantage of making sure all the brake hardware goes back in so they won't squeal! 
    • You miss spelled bearings...
    • Just putting it out there, that's a decent list. You would be better off *not* doing *any* of that and buying someone else's modded car. Like mine. Or anybody else's. Yes it's lotto dependent and all this and that but that 70K (remember, double your guesses) could go elsewhere. Keep it stock, save your money, go lowball @Dose Pipe Sutututu :p
    • Does not mean what you think it means. The continual rising coefficient is the coefficient of friction that continues to rise with increasing temperature. Not "rising during a single stop", except inasmuch as the brakes should get hotter during a single stop. The RR would not be the best choice for a streeter. Yeah....no it's not. JAX would rummage around in the "shit pads we use for all shitboxen that come in here" and install those.
×
×
  • Create New...