Jump to content
SAU Community

Recommended Posts

I think the whiteline bars are $400 - $500 front and rear.

The thing is that I don't want to make the car grossly uncomfortable so I don't want urethane/nolathane bushes.

I got the shocks and strut bars. There's still some money to be spent on brakes as well.

Car is fine and I have a boring 1,000km run in to look forward to.

T.

Link to comment
https://www.sau.com.au/forums/topic/27167-skyline-handling/#findComment-571998
Share on other sites

Sway bars (actually "anti-roll" bars) stiffen the suspension to prevent weight transfer to the outside wheels during cornering. The beauty of them is that they don't affect the straightline ride comfort, which you would get by fitting heavier shocks / springs to achieve the same result.

You should invest in the nolathane bushes - it will reduce the compliance of the suspension, ie the suspension is less likely to change dynamically from its static settings. But they won't contribute noticably to ride (dis)comfort.

It's generally pretty complex subject. I would suggest you invest a few dollars in some books (1 by Fred Puhl is pretty good at explaining the physics, but gets technical when showing how to calculate all the variables).

Link to comment
https://www.sau.com.au/forums/topic/27167-skyline-handling/#findComment-572130
Share on other sites

First thing you need to do is get someone who knows what they are doing to have a look at the car and see what it is doing now. It may be that nothing is suited and the balance etc is all over the place and even that it is too low now and thus does not allow enough suspension travel.

Mick.

Link to comment
https://www.sau.com.au/forums/topic/27167-skyline-handling/#findComment-572144
Share on other sites

Tony, nolathene bushes won't make the ride uncomfortable - the hard Jap springs are already perfect for doing that :rofl:

As blind_elk says, swaybars are perfect for improving handling without affecting ride comfort. What they basically do is link your left and right suspension arms together. As the outside suspension arm travels upwards in a corner, it pushes the swaybar upwards as well. The swaybar then transfers some of this upwards movement to the inside suspension arm, and the net result is that the outside arm compresses less, and you get less body roll through the corner.

Skylines (and most other cars) already have swaybars, but they're not very thick. Whiteline have stiffer/thicker bars, which do the job better. You usually need a bit of bodyroll though, otherwise your inside wheels will start to lift off mid-corner. Happens to the Bathurst V8's fairly often.

Link to comment
https://www.sau.com.au/forums/topic/27167-skyline-handling/#findComment-572841
Share on other sites

Handling on my car is slightly worse than it used to be.

On my car at least, it's a bit of a double edged sword.

There's 12 or 16 levels of adjustment.

The ride used to be harsh but zero body roll.

Now it's soft and pliable but rolls a fair bit.

So maybe the bars might fix that to some degree.

T.

Link to comment
https://www.sau.com.au/forums/topic/27167-skyline-handling/#findComment-573418
Share on other sites

Way to go is a full Whiteline kit. You might find it a little firm on day one but it is so controlled that the ride soon feels fine, even over bumpy surfaces. I opted for the full version with the nylon bushes and adjustable bars because I use the car for supersprints. It cost around $2200 installed and has been a great investment.

Link to comment
https://www.sau.com.au/forums/topic/27167-skyline-handling/#findComment-575472
Share on other sites

I have full coil over suspension by a company called DORF. Its fully adjustable up and down and soft and hard. Its on the softest setting and its damm bumpy. I mean really bumpy in that if your accelarating and go over a bump your wheels come off the ground. Also while going up my driveway, I have 1 wheel (left rear) in the AIR. The car is so stiff it doesn't have any play. Its great for handling, like a car on rails, and with no body roll.

THe disadvantage apart is that if you try to launch the car it wheelspins majorly.

The major advantage, watch those girlees t i ti es bounce around like mad!

:uh-huh:

Link to comment
https://www.sau.com.au/forums/topic/27167-skyline-handling/#findComment-580858
Share on other sites

I've never really thought about this and can see why soft suspension might seem the best for getting off the line but consider this:

If the car sits right down at the back under heavy accelleration, weight transfer may also cause considerable negative camber and therefore less contact area between the tyre and the road. Camber kits, after all, are designed to minimise negative camber on lowered cars and avoid reducing tyre contact area.

Also, I've never seen a serious drag car with soft suspension...

Link to comment
https://www.sau.com.au/forums/topic/27167-skyline-handling/#findComment-581373
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I also built one, for a bit of a laugh. Pretty happy with it. Basically, obtained a clear garnish, painted it sanded back the paint off the letters, clear coated it. Inserted a 3cm EL strip through a slot I created in one end and sealed it up.
    • Apexi SAFC - AFC 1st Generation Rare Old School JDM As you can see it all lights up in the photos and is in 100% working condition. Has been kept in storage and boxed for years there won’t be to many like this if any! Especially with all original packaging and manual. price:$650   APEXi SAFC 2  In Complete Working Condition Refer To Photos and view the video provided.  Price:$500   Located Melbourne - Australia Wide Postage Available At Buyers Expense  IMG_6981.mov
    • wow so i just logged back in after buying the 33 and joining SAU, And I've got all a whole bunch of you wanting to know more, well unfortunately it still doesn't run i was hoping it was seized from a snapped timing belt as i turned it over by hand and it was fine and then it did a few revolutions and jammed solid when i was running it with the key, so the timing belt is mint, I've also found a lot of the parts I'm removing have already got bolts undone or not quiet tight enough to be unsuspicious. so the plan is to find a running RB30 block and chuck my head on it.  I have a habit of buying stuff I don't need or require so for my none running engine i have a forward facing plenum , Apexi power fc, 40mm Turbosmart wastegate, And for the car its self coilovers ,low seat rails and BRZ seats (black seats with red stitching i already had these and they are ADR Approved and allow rear passengers access)  
    • I took apart the dash and found this strange 2 pin connector. it dosen't seem like its factory or oem, any clue on why someone would add it and where it might have been connected too?    
    • Not mention a SS2 especially with that rear oddly small rear housing. I feel the Facebook mechanics and experts has led OP in the wrong direction.
×
×
  • Create New...