Jump to content
SAU Community

Recommended Posts

I think the whiteline bars are $400 - $500 front and rear.

The thing is that I don't want to make the car grossly uncomfortable so I don't want urethane/nolathane bushes.

I got the shocks and strut bars. There's still some money to be spent on brakes as well.

Car is fine and I have a boring 1,000km run in to look forward to.

T.

Link to comment
https://www.sau.com.au/forums/topic/27167-skyline-handling/#findComment-571998
Share on other sites

Sway bars (actually "anti-roll" bars) stiffen the suspension to prevent weight transfer to the outside wheels during cornering. The beauty of them is that they don't affect the straightline ride comfort, which you would get by fitting heavier shocks / springs to achieve the same result.

You should invest in the nolathane bushes - it will reduce the compliance of the suspension, ie the suspension is less likely to change dynamically from its static settings. But they won't contribute noticably to ride (dis)comfort.

It's generally pretty complex subject. I would suggest you invest a few dollars in some books (1 by Fred Puhl is pretty good at explaining the physics, but gets technical when showing how to calculate all the variables).

Link to comment
https://www.sau.com.au/forums/topic/27167-skyline-handling/#findComment-572130
Share on other sites

First thing you need to do is get someone who knows what they are doing to have a look at the car and see what it is doing now. It may be that nothing is suited and the balance etc is all over the place and even that it is too low now and thus does not allow enough suspension travel.

Mick.

Link to comment
https://www.sau.com.au/forums/topic/27167-skyline-handling/#findComment-572144
Share on other sites

Tony, nolathene bushes won't make the ride uncomfortable - the hard Jap springs are already perfect for doing that :rofl:

As blind_elk says, swaybars are perfect for improving handling without affecting ride comfort. What they basically do is link your left and right suspension arms together. As the outside suspension arm travels upwards in a corner, it pushes the swaybar upwards as well. The swaybar then transfers some of this upwards movement to the inside suspension arm, and the net result is that the outside arm compresses less, and you get less body roll through the corner.

Skylines (and most other cars) already have swaybars, but they're not very thick. Whiteline have stiffer/thicker bars, which do the job better. You usually need a bit of bodyroll though, otherwise your inside wheels will start to lift off mid-corner. Happens to the Bathurst V8's fairly often.

Link to comment
https://www.sau.com.au/forums/topic/27167-skyline-handling/#findComment-572841
Share on other sites

Handling on my car is slightly worse than it used to be.

On my car at least, it's a bit of a double edged sword.

There's 12 or 16 levels of adjustment.

The ride used to be harsh but zero body roll.

Now it's soft and pliable but rolls a fair bit.

So maybe the bars might fix that to some degree.

T.

Link to comment
https://www.sau.com.au/forums/topic/27167-skyline-handling/#findComment-573418
Share on other sites

Way to go is a full Whiteline kit. You might find it a little firm on day one but it is so controlled that the ride soon feels fine, even over bumpy surfaces. I opted for the full version with the nylon bushes and adjustable bars because I use the car for supersprints. It cost around $2200 installed and has been a great investment.

Link to comment
https://www.sau.com.au/forums/topic/27167-skyline-handling/#findComment-575472
Share on other sites

I have full coil over suspension by a company called DORF. Its fully adjustable up and down and soft and hard. Its on the softest setting and its damm bumpy. I mean really bumpy in that if your accelarating and go over a bump your wheels come off the ground. Also while going up my driveway, I have 1 wheel (left rear) in the AIR. The car is so stiff it doesn't have any play. Its great for handling, like a car on rails, and with no body roll.

THe disadvantage apart is that if you try to launch the car it wheelspins majorly.

The major advantage, watch those girlees t i ti es bounce around like mad!

:uh-huh:

Link to comment
https://www.sau.com.au/forums/topic/27167-skyline-handling/#findComment-580858
Share on other sites

I've never really thought about this and can see why soft suspension might seem the best for getting off the line but consider this:

If the car sits right down at the back under heavy accelleration, weight transfer may also cause considerable negative camber and therefore less contact area between the tyre and the road. Camber kits, after all, are designed to minimise negative camber on lowered cars and avoid reducing tyre contact area.

Also, I've never seen a serious drag car with soft suspension...

Link to comment
https://www.sau.com.au/forums/topic/27167-skyline-handling/#findComment-581373
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Thanks Dose.....    I appreciate it!!
    • I'll probably be putting the shit box back on the dyno again soon, I want to dial in the closed loop boost control properly. I'll have a camera facing the car/motor for fun too. Just note, there are essentially 3x 10AN inlets going into the catch can and 1x going back to the intake pipe. Most of the time the catch can "return" to the sump actually is the crank case breather, pushing air out.
    • I have the R3C with a Nismo slave and by no means does it behave like a stocker, it ain’t THAT bad. On take off just give a bit more throttle than you would say a coppermix and it’s fine. It will not slip though.   
    • Okay. Final round of testing done. Got a friend to hook up a fancy scanner to the car and we also ran some compression and leakdown tests, she is healthy.  The MAF was definitely the culprit. So for future reference anyone with similar issues that find this thread. I suggest the following steps, in order of affordability:   Check your spark plugs for any fouling, replace plugs if they are bad or re adjust the gaps making it narrower (0.8mm would be good). Check every coil's resistance with a multimeter. It can be done by probing the IB and G pins on the coil pack. Resistance should be around 1.4 (+/- 0.1) Ohms Check the MAF. If you have Nissan connect or a good scanner with the 14 adapter it should allow you to see the voltage on the MAF reading should be around 1.1 - 1.2V when car is idling. But if you don't, buy a new MAF from Amazon and test, then return it. (For instance, I got a Chinese one for $40 that was reporting 1.3v on idle). If you still have scanner, you can run tests on the injectors to see if they are working, just remember to unplug the fuel pump fuse/relay and have no pressure on the line. Then listen for the noises that the injectors make. Clean/replace injectors as needed. Once you find the issue and fix, order thousands of dollars worth of OEM parts to refresh unrelated things (Optional)   PS: Thanks to the absolute legends of this forum for the responses and help to someone that went a bit over their head. (me)
    • Ha ha ha, so they stopped the bearings spinning on the one you want, but then decided the crank hub should slip instead 😛   Stick to RB, at least you can work on it yourself. And now it doesn't smell of vapour   Also I still believe there's a chance your new flap doesn't "pop", as even though the engine might breath hard, it has a direct path with no restriction to the inlet, which when on boost should pull a bit of suction for you. If you do get pressure in the catch can id be very intrigued. Time to put a boost gauge on it, and a session at the track, then solid cover your vent and do another session
×
×
  • Create New...