Jump to content
SAU Community

Recommended Posts

guys i was driving down the freeway the other day not thrashing the car or anything doing aroun 120km/h and put my foot down in 5th to overtake slow car in front and all i got was this whomp whomp whomp through the exhaust but no compression revs up to 2500rpm nothing past there I had to putt putt all the way to nth syd from gosford at 70-80km/h and not got past 2500rpm or the whole car would shudder and now tonight I had to drive it back home and even worse getting less and less compression taking it to the mechanic in the morning but I need to ask you any ideas!!?? Just so the bugger can't rip me off!

I turn the car off and back on and it is ok as soon as I get going same thing happens again?

Also what is the HICAS light and will that have anything to do with it?...

Please help guys!

Link to comment
https://www.sau.com.au/forums/topic/27175-big-problem-help/
Share on other sites

If the car starts and idles ok then it's probably your AFM. Check for a loose plug for a start, that is hopefully all it is. I had the same symptoms when I accidentally yanked out my S-AFC wiring loom, thus causing the AFM to become disconnected.

Not sure if the HICAS has anything to do with it, mine never came on when I had this problem.

Link to comment
https://www.sau.com.au/forums/topic/27175-big-problem-help/#findComment-572089
Share on other sites

I had a search through the threads last night and it sounds exactly like this except mine shudders and ****ters when i put my fot down

"HELP !- losing a cylinder in the rain :D

As topic states:

losing cylinder(s) when parked outside in the current Sydney weather for 6 hours on an otherwise stock ECR33. after a while (quite a while) & some heat it comes good. The plugs are newish and the Datto has never missed a beat.

Are S1 RB25's prone to this ??

has anyone else experienced this ??

It's kinda spooked me... "

Yup, adam's spot on. it'll sound like a WRX just off idle & runs about as bad as an engine can without stalling !

Swapping the pos of the coils on the alloy mount... well I'm dead certain the moisture was between the coil & mount and that by simply removing/inspecting/cleaning/silicone spraying/replacing (with sighted good ones) the known faulty ones came good !!

Also I eyeballed the sus coils arcing (up to 12mm !!) to the alloy mount from their bases which was a bit of a giveaway.

I reckon seeing is believing, & there's been a lot of threads about coil pack testing involving swapping coils and tossing the failing ones. So how many perfectly good ones get tossed !!

Using the "Crank & Eyeball" test, if the coil is good you should see a spark, but NOT necessarily at the plug electrode !

If no spark do the GraemeW test. Many have questioned the validity of this test, but if it fails it's well & truly dead. I know from searching these forums that other members coils' have passed the resistance test but got binned anyway, consequently the rumour exists that this test is unreliable - methinks not !!

P.S. I gapped the plugs to .75mm and no more miss under load @4500rpm above 8-9 PSI with stock ECU. Jay95 posted about this in another thread & I give it the full thumbs up.. gap 'em down with confidence.

so do you think it could be the coil packs?

Link to comment
https://www.sau.com.au/forums/topic/27175-big-problem-help/#findComment-572109
Share on other sites

Yep definitely could be coil packs, it's just hard to understand exactly what the problem is going off a written description which is why I suggested AFM. Also I just noticed you said it's getting worse, if it's AFM then it's all or nothing (ie it won't get any worse). Check your coil packs too.

Worst case it's your rings or something, in which case you should probably look at your state of tune because they probably shouldn't just go like that with regular driving.

Link to comment
https://www.sau.com.au/forums/topic/27175-big-problem-help/#findComment-572115
Share on other sites

Well, if it all happens at 2500rpm, I am tending to agree with JimX's first impression - AFM.

Generally the cut is at 2500rpm from limp home mode.

Check for loose wires and try giving the AFM a clean, but first, have you tried doing an ECU diagnostics?

Like all things car though, you can never be 100% certain what it is until you have tried eliminating the possibilities:)

Link to comment
https://www.sau.com.au/forums/topic/27175-big-problem-help/#findComment-572286
Share on other sites

Sorry mate extreme newbie here as far as maintaining the car myself always goto a mechaninc... AFM? Air Fuel Meter? and how would i try doing any ECU diagnostics?

I took it too the mechanics today left it there all day and the bloody thing did not play up once and he can not see anything wrong I drove it home and around the coast for bout 1hr and no probs... could it have something to do with the rain i was driving in?... I don't see how has never been a prob b4.

What loose wires would i be looking for? thanks for your suggestions so far guys please help me out more if you can! thanks!!!

Link to comment
https://www.sau.com.au/forums/topic/27175-big-problem-help/#findComment-573049
Share on other sites

If the problem has fixed itself then your engine is definitely fine :D It sounds like an intermittent contact in your AFM (Air Flow Meter). This is the thing just behind your air box, it measures how much air is going into your engine. Unplug the small wiring connectors and spray with some electrical contact cleaner (get it from Jaycar), plug it back in and try again. Also spray the AFM filament with the contact cleaner. Do a search on cleaning the AFM for more detailed instructions.

Link to comment
https://www.sau.com.au/forums/topic/27175-big-problem-help/#findComment-573105
Share on other sites

I got a bit enthusiastic cleaning the engine bay and a day later the barge started dropping cylinders under load. Fine off boost and stumbling at idle so I whipped out the coil packs and water had filled in 3 of the plug wells and was seeping past the rubber weather seals. Even so the damage was done and a serious coating of baked on crap is right up the ceramic insulator on a few of the plugs. I tried to clean most of it off but was still dropping a cylinder so a new set of 7 heat range standard plugs gapped to 0.8mm has solved the problem and it's delivering more power than ever. And I was worryng it would be a coil pack.

I leave the plug cover off with the copper plugs so i can clean and gap them every time it starts to get rough under load....about 5000km but the power is better than the platinums.

Sounds like [some of] your plugs got water around them and were not firing in some cylinders. After 18 years of racing cars, swinging spanners for a living and getting a mechanical engineering degree I still find that plugs are the number one culprit for lost power and misfires.

Link to comment
https://www.sau.com.au/forums/topic/27175-big-problem-help/#findComment-573191
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Ah yes, fair enough! I was purely thinking about cleaning the spokes and front of the wheel with the mitt. For the barrel the rag on a stick makes more sense. I've tried cleaning the barrels on mine and gave up in frustration. Between brakes being in the way or spokes being in the way and limited space to constantly move the car front and back it was just too annoying. The barrel being as shiny as the rest of the wheel sounds amazing though. At this point I'm not even sure if they have the same surface finish on mine. But I feel inspired now to find out.
    • I have a wheel cleaner pokie thing which is a glorified microfibre rag on a stick, and there is not sufficient clearance between the caliper and the barrel to clean that section. I just roll the car forward 500mm and have another shot at each wheel.
    • The "rag on a stick" is a easy way to fit in between the wheel spokes into all of the barrel Albeit I do have 10 spokes on the MX5 which limits the access to actually jam my hand in to clean the barrel, but it was also makes much easier to clean the 5 spokes on the Dunnydoore with it as well, as you don't have to worry theΒ  caliper getting in the way if you have at least about 15mm space between the caliper and barrel This of course depends if you actually have the clearance between the barrel and caliper, and the amount of OCD you have to get the barrels as clean and shiny as the face of the wheel The thing is bendy as well so you can actually shape it to conform to the inner lip of the barrel Β 
    • FWIW, as well as a basic immobiliser/remote unlock (all basic units give you those 2 things), I would also install a 4g tracker in any car I cared about. Just hide it anywhere that won't be found in a rushed look and preferably get something with a built in battery backup so it stays online for a while when the battery is removed or flat While its not a car, when our car trailer was stolen in that den of crime Sydney about a decade ago, the cops were watching from the bloke's neighbour's lawn within about 2 hours until he started swapping the plates and putting up the gumtree ad.Β Β  Obviously it is still not undefeatable (eg parking it up for a few days somewhere without sky sight) but it greatly improves your chances of getting it back quickly and with less damage
    • Instead of magic keyphrases I wonder if something can be done with auto complete. Similar to how user names are handled already. When you type '@' and follow with letters, it'll search across all usernames. It might work to have the same for forum topics. Some key to trigger it and then text search across all thread names and it'll insert the name and URL when pressing enter.
Γ—
Γ—
  • Create New...