Jump to content
SAU Community

Spark Plug Broke Off In The Engine!

R33Matt

By R33Matt,
in Engines & Forced Induction

 Share

Recommended Posts

R33Matt Collaborator

R33Matt

Posted
Posted

Im having a bit of trouble with a spark plug in my mates Skyline. When I started to unscrew it, it snapped! Only took a little bit of presure and it broke apart. I have changed the plugs on skylines heaps of times and ive never seen this happen before. The plugs were called "Autolite" and were put in by the guy before him. It seemed to snape at the where the metal part is of the spark plug. Its still screwed in there, Is there any way of getting it out? Some kind of special tool?

Any idea would be Great!!

Thanks :D

Link to comment
https://www.sau.com.au/forums/topic/271865-spark-plug-broke-off-in-the-engine/
Share on other sites
James_03 Mentor

James_03

Posted
Posted

From your description sounds like the porcelain has broken apart. This has happend to me a couple of times before, on my own car and others.

They were probably incorrectly torque down during previous installation. What I have done in the past is get a vacume cleaner in there, a good hi-powered one and remove as much loose porcelain as you can from the cylinder head valley. Check to see if there are any bits you can gently remove from the plug, large pieces.

Then vac it again and start to gently take the plug out. I usually get someone to hold the vac around the base of the plug whilst I remove it.

I have done a few in the past all went ok, just have to take your time with it.

doo doo Proficient

doo doo

Posted
Posted

Happened to me too, new clean threads shouldn't be tightened too much. Was lucky though- if it's broken past the hex a possible scenario is to chip the porcelain down and use an easy-out for the plug body. Though mine actually loosened in the process of chipping away the porcelain. Be careful as the porcelain could be pushed through the plug and into the cylinder.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      I had absolutely no symptoms whatsoever that anything was wrong.... I'm very happy it was all spotto'd and re-bled and re-torqued and aligned though. Will be picking it up tomorrow and undoubtedly be like "Oh, that clunk is gone" "Oh, the car really wants to drive straight" "Oh, that pedal feels better" "Oh, it feels like I've gained 25hp" "Oh, the handbrake works now" It should have been a sign that the new Project Mu shoes had 3mm of pad depth on them out of the box, and the OEM ones from 25 years ago that we took out also had 3mm of pad depth, implying the issue was not, and never was the shoes, but we put that down to it not being adjusted correctly. It wasn't, but it wasn't even adjustable at all given one side was boned and the T Junction of the cables was on a 45 degree angle, the non-working side being the one on the massive angle. Obviously when I had adjusted it and reset it and re-tensioned it I had either got it stuck or something along those lines. Oh well. Live and learn and absolutely could have been catastrophically worse so I'm rationalizing it as a win, kinda. I also got the chance to measure the distance between rear rim and the suspension arm/shocks and found a 30mm rubber block only just doesn't fit there. Which is great to know before ordering wheels, when I assumed 30mm was easy. The man with the Porsche adapters has rims that use 23.9mm of that space, so it's safe to assume I have between 23.9 and 29.9mm of space there to play with on the inside. The wheels looked pretty stupidly pokey with the 20mm spacers on the rear, only for me to find that the studs come out another 12mm and the wheel doesn't actually sit flush with the hub because you're supposed to cut your original studs. The wheels do have cutouts that kinda accomodate it, but not fully. So my 20mm spacer was anywhere between 25mm and 35mm. ~25mm and send it will determine on where the wheels sit with the spacers on. When I put the pads in for the track day I will mess around with spacers (with wheels that do not clear studs properly when mounted to spacers) and do more math, for the last time, for the 7th time.
    • The Bogan
      Mistakes were made, my R34 Story

      By The Bogan · Posted

      Lucky pick up Best to find these things before something horrible happened to the yoke flange thingies I would hate to think what would happen if it dropped the tailshaft  Hopefully the holes are not flogged out in the yokes and it was just the bolts that got munted  As for the hand brake.....ouch, look like the disc got rather hot, and I assume smokey, I recall when I had a front caliper seize on the Commodore, there was lots of smoke and the disc was glowing cherry red when I was able to eventually stop and have a look, and stopping a big heavy car, going down a big hill with some rather high RPM down shifts and some hand brake action is something that makes you think hard about life
    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      One of the things that never seemed right was the handbrake. Put in some nice new Project Mu shoes. We figured the rears were out, so why not. We're right there. My handbrake never worked well anyway. Well, this is them, 15km later. 67fdcf94-9763-4522-97a4-8f04b2ad0826.mp4 Keen eyes would note the difference in this picture too:   And this picture: Also, this was my Tailshaft bolts: 4ad3c7dd-51d0-4577-8e72-ba8bc82f6e87.mp4 It turns out my suspicions that one side of the handbrake cable was stretched all along were pretty accurate, as was my intuition that I didn't want to drop the tailshaft to swap them on jack stands and wasn't entirely sure about bolt torque. I have since bought the handbrake cables which have gone in. I'm very glad that I went to my mechanic friend who owns an alignment machine to get an alignment before the track day, because his eyes spotted these various levels of "WHAT THE f**k IS GOING ON HERE?". Turns out the alignment wasn't that bad, considering we changed the adjustable castor arms out for un-adjustable castor arms, and messed with the heights. Car drove pretty good with one side of the handbrake stuck on, unbleedable rear brakes, alignment screwy, and the tailshaft about to go flying and generally being a death trap waiting to happen! (I did have covid) (I maintain I adjusted the handbrake correctly, but movement caused shennanigans and/or I dislodged the spring on the problem side somewhat, or god knows what). G R E G G E D
    • 32.det
      My R32 Money Pit & The Headaches That Come With It

      By 32.det · Posted

      Very interesting, im not sure how all those complications fit in to running a haltech instead of a stock ecu but I'm starting to think I'm a bit out of my league.
    • GTSBoy
      My R32 Money Pit & The Headaches That Come With It

      By GTSBoy · Posted

      I just put 2 and 2 together. This is a Neo converted R32. The Neo ECU (in concert with the R34's AC controller) runs the AC quite differently to how the R32 ECU and AC controller do it. If you just drop it all in, it won't work. There is some tricky wiring required, including changing to the pressure switch that the Neo controllers want to see. I don't know what it is, because mine was done by a guru. It was a year or so after I did that transplant before he worked out what needed to be done.
×
×
  • Create New...