Jump to content
SAU Community

Recommended Posts

what are legal positions for front number plate? after getting my car resprayed i want to mount front number plate on the side but dont know which side?

i already had cops trying to defect me for number plate angle and only 2 screws coz they couldnt find anything else, so i wanna be sure before i drill any holes in freshly sprayed front bar.

Link to comment
https://www.sau.com.au/forums/topic/272186-number-plate-position/
Share on other sites

i dunno whats legal but i have mine mounted on the left and ive had many cops look at my car and not say anything about it :rofl:

i think its got to be about 100mm off the ground to be legal or something , might have to call regency up mate

passenger side. only reason i chose that side is a lot of cars that come from the factory with offset plates, have em on that side (ie alpha romeo).

dont think they are to fussed on which side they are on. but it would make sense to have them on the drives side though, that way on-coming traffic can see it with ease

OK..

i was pulled up by a cop at a car park on one of kell's cruises,

i had it on the passenger side, right down the bottom of the bar.

she didnt mind it being on the side, or on an angle, but said it had to be ATLEAST 30cm off the ground.

first hand info right there.

I'm not sure about the ruling in SA, but in Vic it must be legible when viewed from a 45-degree angle from either side of the car.

Its about 20 degrees maximum in the official transport SA guidelines but like craig said, they're more concerned about visibility and height - I've never had any issues with my plate, it went thru regency fine with the relocation kit and that has around a 10 degree angle

-D

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • What can't be done with a little bit of decking board or similar timber bolted to a hub flange via 2 wheel nuts is not worth talking about.
    • I noticed something. On the tps sensor and the sensor behind the adjustment screw is adjusted towards the far left. Are these screws supposed to be centered? (this sensor was in the same position before the tune as well)  Also attached a photo of where my car usually idles at when warm (sometimes a tiny bit above that). I think I might have screwed up the calculation and it might have better than I thought lol at 750rpm still not 650rpm though.      
    • So for both general interest of engine health, and to rule out any coolant/oil issues, I organised an oil analysis done on the 125,000klm oil Results below, all good, just a bit of fuel dilution which I'm not too worried about
    • This is actually a really good way of measuring what wheels fit. If only there was a similar measurement between hub face and suspension :p That said, it's probably pretty simple to actually measure it all with the wheel off the car for the rear. The front is a bit more complex but.. 
    • Being the top Google search result for R34 wheel-related inquiries, lemme throw down my experience. I calculated that 100mm from hub face to wheel face is about the perfect fitment for my ENR34 sedan.  I've been running 18x8.5s, ET35, with a 1" spacer. So, 8.5in to mm = 216mm. 216/2 = 108mm. 108-35 = 73mm. 73+ 25 (1" to mm) = 98mm.  If you wanna get close to this on dif widths, here are the offsets you'll want: 9" - ET around 15mm 9.5" - ET around 20mm 10" - you're crazy, but ET around 30mm All these should fit perfectly on a non-widebody, non-GTR Skyline. Note that it's probably the absolute max, and you're probably better off running a couple degrees of camber in this config, but it looks great, super flush.
×
×
  • Create New...