Jump to content
SAU Community

Recommended Posts

WHAT THE F**K?!

What a waste to put these wheels on an Integra!

Rays Engineering - Volk Racing TE 37's are one of the best wheels to come from Japan and you reckon to put it on an Integra.

;)

:thumbsup:

The looks friggin tuff on GTR's.

post-46584-1244088007_thumb.jpg

LMFAO! :thumbsup:

Spunky Munky you say some stupid things on SAU I can't help but laugh!

It's not a personal attack, all cool! :yes:

Back On Topic.

Royalflush, have you got a price in mind?

Selling these wheels with no tyres you can easily get $2000+

But depending on the condition of the wheels too, gutter rashes, scratches, paint etc...

I would keep them as I have set of 17" TE37's myself and they are very nice wheels.

hey mate, sorry to but in to your post, but can you tell me wht size and offset those Te37s on the white r33 gtr u posted are? i mean like an exact size, coz i want the exact same size and offset for the gtr im goin to buy in a few months,

cheers

are you negoiable on this price? A set of 18 inch bronze ones in imac condition just sold on these forums a couple of weeks ago for $2000 with rubber. For second hand 17s with marks on them i think it may be a bit much. I'd definately be interested if the price was better.

Would they fit an R34GT

If 34GT is 5x114.3 yes they will fit nicely.

are you negoiable on this price? A set of 18 inch bronze ones in imac condition just sold on these forums a couple of weeks ago for $2000 with rubber. For second hand 17s with marks on them i think it may be a bit much. I'd definately be interested if the price was better.

Mate you sold them really cheap. TO be honest you lost money on them.. taking in to consideration the exchange rate and how hard it is to find a nice set these days with good Japanese Rubber is pretty rare. 2.5K is fair price. I'm open to offers.

Shoot me a PM =]

Guys i don't really know how they will sit on your car so If you want to know look on the wheels sections or use this site as a guide.

Offset Calculator

Pm received Dush.

Edited by Royalflush
Hey boys/girls.

Thinking of Sellin my TE37's... not sure yet as i dont have any rims to put on the car if i was to sell em..

Wheel Spec's:

White TE37's

front: 17x8.5 +30

rear: 17x8.5 +30

For those who dont know what they look like. (I'm sure there is always 1. lol) Here is a pic!

They have RE01-R's on em.. 80ish% thred.

EOI price: 2.5k

myskylineuj7.png

PM me DECENT offers People. I really need em gone.

  • 3 weeks later...
  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I know this one鈥檚 the BB one. My tuner did make mention about the actuator. I am curious about the VCT as well
    • Might also needs a stronger actuator with the right preloading. With older 2019 built bush G3 units, BB upgrade or 21U housing down size makes a pretty decent gain in response as well. 
    • Hey lads  so im finally putting together my rb30 forged bottom end and ran into an issue. I measured my main bearing clearance with arp main studs torqued to 60 ft-lbs using ACL H series STD size bearings and standard, un-ground crank shaft journals and got an oil clearance reading of about 1.3 thou measuring straight up and down and about 2.8 thou measuring at a 45 degree angle (just above and below the parting line). My machine shop said they measured the main tunnel and it was all within spec (they didnt say the actual measurement) and to go with a standard size bearing, which i have done and the clearance is too tight, I'm guessing because of the extra clamping force from the arp studs distorting the main tunnel. I was wanting to run about 2.5 thou main bearing clearance.  My questions are: 1. could i just use the HX extra 1 thou clearance ACL bearings? that would fix my straight up and down clearance making it about 2.3 thou, but then would the side to side clearance be too big at around 3.8 thou? 2. what actually is the recommended main bearing clearance for measuring near the parting line / side to side. i know its supposed to be bigger as the bearing has some eccentricity built into it but how much more clearance should there be compared to the straight up and down measurement? at the moment there is about 1.5thou difference, is that acceptable or should it be less? 3. If i took the engine block + girdle back to the machine shop and got them to line bore the main tunnel (like i told them to do the first time, but they said it didnt need it) what bearing size would i buy? the STD size bearing shells already slide in fairly easily with no real resistance, some even falling out if i tip the girdle up-side-down. If im taking material out of the main tunnel would i need a bearing with extra material on the back side to make up for it? this is probably confusing af to read so if something doesn't make sense let me know and ill try explaining in a different way. My machine shop doesn't come back from christmas break until mid January, hence why i'm asking these questions here. TIA for any help or info 
    • I bought the model back in Japan in Feb. I realised I could never build it, looked around for people who could build it, turns out there's some very skilled people out there that will make copies of 1:1 cars or near enough. I'm not really a photo guy... but people were dragging me in a group chat for the choice of bumper as someone else saw the car before it was finished as they are also a customer of that shop. I took the photo in the above post because I was pretty confident that the lip would work wonders for it. Here's some more in-progress and almost-done pics. It gives a good enough idea as to what the rear looks like!   I have also booked in a track day at the end of January. Lets all hope that is nothing but pure fun and games. If it's not pure fun and games, well, I've already got half an engine spare in the cupboard 
    • Well, do ya, punk? Seriously though, let's fu<king go! The colour and kit looks amazing on the car. Do you have any shots from the rear? I don't quite follow how the model came around. You bought the white kit and he modified it to match your car? Looks nuts either way!
  • Create New...