Jump to content
SAU Community

Rb26 Engine Parts


Recommended Posts

  • Replies 46
  • Created
  • Last Reply

Top Posters In This Topic

The parts up for grabs have a cheaper price than the original (nearly all the goods except a few)!!

Wiring loom (unmolestered) $400

R34 GTR intake plenum $80

Throttle bodies + linkages $300

Intake manifold assay (injector plate) $300

Head (complete and acid dipped and treated) $1000

Crank $300

Power steering bracket $10

Crank pulley X2 $40 each

Exhaust manifolds X2 $30 the pair

Block $200

Crank girdle and crank scraper $100

RB26 stock fuel rail + reg $50

Coil packs and brackets $100

Oil filter assay $100

Oil + water lines $50

AAC valve and air chamber $150

Air regulator (idle control) $80

CAS and mounting bracket $100

Alternator $50

Throttle valve switch $40

Twin turbo connecting pipe X2 $20 each

R33 centre grille with mesh $100

R33 front bar (N1 replica bar) no indicators though $200

ANY INTEREST IN THE ABOVE PARTS SEND US A PM

Link to comment
Share on other sites

INTAKE PLENUM, THROTTLE BODIES AND THROTTLE VALVE SWITCH ****SOLD**** (BAHAIMUS)

Other parts still available! Send us a PM if you are in need of any of these things!!

hey mate, can you contact me on 0414 913 548, interested in the head.

Thanks David

I also live in Adelaide

Edited by calaisturbo5speed
Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share




  • Similar Content

  • Latest Posts

    • Yes sir, that was me. Fake ARP's are also a thing over here in Canada and we only order from reputable dealers. It's sad that even simple things like bolts and hoses are now also being copied... anything to make a dollar.  Story time. Like all cheap crap from China, it's even an issue with firearms. Roughly 15 years ago, I purchased a new cheap Norinco 12g shotgun. First time out in the bush with it, while firing, bolt assembly didn't lock and it fired out of battery. The receiver also being cheap steel, basically exploded in my face. I was lucky to be wearing eye protection. Long story short, don't buy Chinese junk. Also Norinco being state run and their only military arms producer, if ever they do try and take over a country, don't worry about it lol. 
    • Installed  Nismo coppermix twin competition spec last year in my bnr32 with pull trans with Oem slave cylinder. The point at where the clutch disengages/enages is right at the top of the clutch pedal, meaning I barely have to push the pedal down for the clutch to be disengaged.  You guys that have the same combo are you experiencing this high pedal bite point??   Secondly I’d like to have the disengagement point lower meaning I have to push the pedal more(further not effort)for it to be disengaged.  I’m thinking to use a Nismo big operating cylinder(bigger bore at 13/16 vs Oem 3/4) which will require more pedal stroke to get the equivalent movement at the clutch fork. But I see Nismo web site says not to mix these 2 as the Nismo big operating cylinder doesn’t have enough stroke to disengage??? Any folks run both the coppermix twin pull with Nismo cylinder??    Thanks in advance for the replies but prefer only guys with pull clutches to respond. thanks     
    • Any chance u could let us know where your based ?
    • That’s a great deal and I would jump on it if you were closer. Melbourne is a bit of a hike for me though unfortunately 
×
×
  • Create New...