Jump to content
SAU Community

Recommended Posts

Hay guys why do the Formula one teams cool the fuel down before it goes into the cars ?

And i was reading that fuel pump is cooled by the fuel passing throught it so would it warm up the fuel ?

Wont this do the opposite to what the formula 1 teams try to do i assume that they cool the fuel down because it makes more power some how which you guys will hopefully

be able to help me with.

The fuel pump warms the fuel up so it makes all the cars less efficent if the fuel is warmer ?

I assume that it makes the the air intake temps lower as it is sprayed into the piston is that what cold fuel dose ?

Link to comment
https://www.sau.com.au/forums/topic/272919-y-cold-fuel-f1/
Share on other sites

It could be a safety thing - colder fuel is less volatile, so not as much vapour around to ignite on hot exhausts / brakes / etc.

But colder fuel is denser, so they can fit a few extra litres in the tank.

Link to comment
https://www.sau.com.au/forums/topic/272919-y-cold-fuel-f1/#findComment-4633351
Share on other sites

But colder fuel is denser, so they can fit a few extra litres in the tank.

yep yep

fuel at a colder temp is smaller in volume than at lets say ambient or warm

therefore they can chuck in more fuel in a standard specified tank.

also a controlled temperature allows them to calculate fuel stops and reduce a variable to make calcs on future stops more accurate.

Link to comment
https://www.sau.com.au/forums/topic/272919-y-cold-fuel-f1/#findComment-4633594
Share on other sites

  • 5 weeks later...

I would add that unused fuel eg; when the throttle is closed, is returned to the tank. Which in our case means the fuel has been around the hot engine bay and picked up heat on its travels. When the car has a huge fueling system to cope with its demands at full power, the fuel can do several laps of the engine bay just idling at a set of traffic lights. This is why Skylines standard have ECU controlled voltages to the fuel pump, when the engine demands are low the ECU limits the voltage eg; 9 volts instead of 12 volts, which means the pump pumps less fuel.

This is particularly important for E85 users as ethanol has a lower vaporisation temperature than petrol. This is what causes the more frequent stalling and acceleration hesitation during and after pit stops for the V8Supercars.

Cheers

Gary

Link to comment
https://www.sau.com.au/forums/topic/272919-y-cold-fuel-f1/#findComment-4702140
Share on other sites

Hay guys why do the Formula one teams cool the fuel down before it goes into the cars ?

There are a number of reasons

1. Cold fuel is more dense.

2. Hot fuel will vaporize.

3. The cars dump a massive amount of heat into everything.

Historically cooling the fuel was at its most important when the cars were limited to 150 litres for a grandprix. This was in 1988 for the turbo cars from memory. The extra few % of fuel gained was invaluable.

Presently you are only allowed to cool the fuel so many degrees below ambient. This is what BMW got in trouble about at the Brazillian GP a couple of years ago.

And i was reading that fuel pump is cooled by the fuel passing throught it so would it warm up the fuel ?

All pumps are affected by the temperatures of the fluid passing through them. All pumps heat up the fluid they are pumping - the most pronounced example of that being your turbo.

As an aside if you think of the 20000+rpm the F1 motors used to run at then you can get an idea of the tiny period of time the injector has available to deliver fuel to the motor. To help in this regard the pressures run in the fueling system in the F1 cars are, by comparisiion to road cars, massive.

Wont this do the opposite to what the formula 1 teams try to do i assume that they cool the fuel down because it makes more power some how

Yes but there is nothing much you can do about it other than increase the efficiency of the fuel pump or lower the rail pressure.

The fuel pump warms the fuel up so it makes all the cars less efficent if the fuel is warmer ?

I assume that it makes the the air intake temps lower as it is sprayed into the piston is that what cold fuel dose ?

Broadly - the hotter the fuel the more prone you are to having pumping issues & vapourisation issues. Also a cooling inlet temp can allow more ignition advance giving more powah.

Some fuels have a marked cooling effect on the inlet system. Alchohol based fuels particularly. The old turbocharged indy cars did not need to run intercoolers simply because of the fuel they used.

Link to comment
https://www.sau.com.au/forums/topic/272919-y-cold-fuel-f1/#findComment-4702203
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • And make sure the belts are tightened appropriately too.
    • They care about emissions, and cost the most. Save weight where possible, and make manufacturing easier. Less material also let's the engine transfer heat to water quicker, and bring the engine up to temp quicker, better for emissions and getting them past their warranty period.
    • I was under the impression the reason why OEMs are going with solutions like relatively thin "right-sized" cylinder walls with technologies like PTWA and open deck is because they care a lot about whatever marginal knock margin benefits they get from that vs the structural rigidity benefits of a closed deck block and thicker cylinder walls. I also see some weird stuff like plastic inserts in the water jacket around the cylinders to try and equalize cylinder wall temperatures. re: the PRP blocks and heads at the end of the day it's hard to know what is and isn't going to work there, just have to see what the initial buyers say about it.
    • Which is why I didn't mention that hardness testing, and specifically mentioned the bore and deck thickness testing. Yeah, not really. The bore temperature will be a lot more even around the top half inch or so, where the material distribution is dominated by the deck, and which is the only place where the bore surface temperature heating any gas in the cylinder is likely to have any effect on detonation. Think about it. Another inch or so down the bore, you might have a hotter spot. The gas there might get a bit hotter, then the piston rises squeezes that gas away from there at high speed and mixes it with other gas from nearby. Instant dilution of the problem. I'd be surprised if it was an issue at any time other than in racing engines or OEM dev engines being run at the ragged edge of tuning. Say what now?
    • https://dsportmag.com/the-tech/education/engine-tech-material-hardness-testing/ The PRP testing on block hardness I'm not sure how much it actually can be trusted. The thinner cylinder walls on RBs is a bit of a problem vs 2JZ but it really depends on the design goal. Siamesed cylinder bores like a 2JZ cause uneven cylinder wall temps too, which means a bit of distortion induced by that + the hotspot can affect knock margin. Something that actually gives me a bit of pause with the PRP block, whether super thick cylinder walls are going to keep it from being drop-in compatible on an otherwise OEM rebuild. 
×
×
  • Create New...