Jump to content
SAU Community

Recommended Posts

I have been planning on buying a eManage Ultimate for my RB20 as I will be upgrading to an RB25 when the engine dies. I figured as it is a piggyback it will be very easy to change over. I have now found a RB20 Power FC at a decent price which I am considering purchasing. I was wondering if I would be able to run a 25 on this whenever I need to change. From what I can see the pinouts are slightly different, and that running a RB25 PowerFC on an RB20 is easy, so am I right in thinking doing it the opposite way around would be fine?

As I understand it I would just need to get it retuned(obviously), and that I wouldn't have VCT. Is this correct?

Link to comment
https://www.sau.com.au/forums/topic/272997-rb20-power-fc-on-rb25/
Share on other sites

if it was me i would be just putting a nistune daughterboard into the stock rb20 ecu and going that way (depending on just how cheap the PFC you found is). it will require you to use the rb20 loom, but my mechanic said that is how he would do it if he was to do the swap again (recently put a rb25 into his ceffy)

if it was me i would be just putting a nistune daughterboard into the stock rb20 ecu and going that way (depending on just how cheap the PFC you found is). it will require you to use the rb20 loom, but my mechanic said that is how he would do it if he was to do the swap again (recently put a rb25 into his ceffy)

I've considered that but the tuner I am going to seems to be most comfortable with Power FC's and eManage ultimates. They also seem to be a more adaptable and popular ECU. I'm in Canberra so the market for tuners isn't large. I might look at the option anyway, could always go up to Sydney and get a Toshi remap done.

Thanks. I think I'm going to buy it then because if prices stay stable I can always sell it for more than I payed. One more question, I was playing with a HC today on a friends car as well as looking over the Power FC FAQ site and couldn't see anything to set the Power FC to default.

The one I'm buying will be running exactly the same setup as mine however I would like to set it to default before all the parts are installed to make sure it runs ok. Is there anyway to do this on the unit?

Cheers,

Adrian

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Are those 1000cc side feeds? If so, that's part of your problem. I have 1480cc and they idle at stoich on 98RON, and all the way to E85. Also your coil packs.....
    • Update for the sake of closure   Ended up getting the intercooler piping all sorted, new plugs and yellow jacket coils, and she was idling mint until it warmed up while I was bleeding the cooling system. Found the misfire to be localised to cyl 3 by unplugging coilpacks, ran a compression test, that checked out, then decided to get a mate to check if that spark plug was firing out of the motor. Upon cranking it over, with the injectors disconnected, the car actually fired and ran on a couple cylinders and heaps of fuel came out the top of cyl 3 I'd say that injector's either spraying incorrectly or spraying far too much, which is fine as I'm planning on replacing them anyway I'm planning on making about 250kW on flex fuel, and have a set of 1000cc injectors from ozautosport, obviously overkill but I'm planning on building the motor and running more boost further down the line, do you reckon they'd be too big for a smooth idle on 98? Thanks for the replies gents, much appreciated
    • I'm confused. You said you want to "remove the clear coat from most panels" but it sounds like you are actually doing a full respray? Few random things to add -  If you chase the blistered paint with 120 grit, I can almost guarantee you'll chase it down to bare metal (that's fine). But if you paint the car from here, you'll have nice little indents where ever the blistered paint was. The new paint won't magically level out the low areas, you need to fill them. Which leads me to the main point I wanted to add, make sure the whole car is flat before you paint it. All those areas with blistered paint you sanded out, make sure to fill them and triple check they are flat with a block guide coat. I'd also check the whole car is flat with a large block and guide coat but yeah up to you if you want to go that far.   
    • 300hp (225kw) is barely outside the standard turbo's range with a bit of extra boost in it (200ish). If you are going to change the turbo you should aim for 250-300kw (330-400hp) to make the expense worthwhile
×
×
  • Create New...