Jump to content
SAU Community

R32 Gtr: Very Difficult To Select Gears

omega36
 Share

Recommended Posts

omega36 Proficient

omega36

Posted
Posted

Ello.

I have a bit of a problem with me clutch/gearbox - 1st is very difficult to select, and 2nd also gives me trouble (and even 3rd slightly shows some resistance) but especially the reverse gear..

Now I'm quite sure it's not the gearbox (?) as I initially thought, but more the clutch - the reason I say this is that even though the clutch is fully pressed down, when I select reverse (eventually after quite a struggle), it feels as if the gear is now engaged as the car starts to move slowly (on a flat plain).

Also, my clutch has recently become (more) heavy... so the problem wouldn't be simple like a stretched clutch cable would it? It's a GTR, so it can't be a simple problem.....

Anyway - the car is off to the mechanic tomorrow, would like to just have some idea of what it may be before I take it there.

Cheers for your help! :laugh:

2LV8ETR Mentor

2LV8ETR

Posted
Posted
Argh. Sounds expensive. Do you know if it's a painful job and if it's expensive? :laugh:

You can do it yourself with a 12 & 14mm socket, a phillips screwdriver, a pair of pliers, and a rebuild kit for about $15-20 for each.

Piece of cake.

omega36 Proficient

omega36

Posted
  • Author
Posted

Hey guys -

We actually found that the clutch booster cylinder has split so there's an air leak there, so that's being replaced. Also getting my leaking ABS unit replaced as I assume the brake master cylinder also needs to come out of the way for the clutch booster cylinder to be replaced.

I hope there isn't a problem with the clutch's pressure plate as well :)

The GTR strikes the bank again ;)

Monky Apprentice

Monky

Posted
Posted

Yeah what was the verdict I have the exact same problem, 1st and reverse are almost impossible which makes traffic lights interesting.

Can you let us know what it was, from what I have ready usually clutch related i.e worn cover, pressure plate or both. I'm running a OS Giken twin plate which has already been refurbished back in 2006, loooks like it's time again!

M

paulR32gtr Mentor

paulR32gtr

Posted
Posted

I had a similar problem with my previous clutch.

I had a leaking slave cylinder so had that replaced. When they installed it they didn't bleed the clutch fluid properly, I noticed it was a little crunchy on the way home when I picked it up but kinda came and went.

Had zero time to do it myself, and the workshop were too far away, so kept driving, clutch pedal kept getting heavier and heavier, hard to get into gears sometimes. Clutch wore out as it wasn't disengaging completely, then pivot ball snapped and fell out the bottom one day.

New clutch for me. Had a lot of other stuff being done around the same time so new clutch made sense anyway - thats how I justify it....

Monky Apprentice

Monky

Posted
Posted

Thanks for the reply Paul, do you think having air in the system contributed to your clutch failure or would you say it was worn regardless?

I'll have a look at my slave and master shortly and see anything dodgy. My car is running just shy of 600hp so it's possible mine is just worn from use.

M

I had a similar problem with my previous clutch.

I had a leaking slave cylinder so had that replaced. When they installed it they didn't bleed the clutch fluid properly, I noticed it was a little crunchy on the way home when I picked it up but kinda came and went.

Had zero time to do it myself, and the workshop were too far away, so kept driving, clutch pedal kept getting heavier and heavier, hard to get into gears sometimes. Clutch wore out as it wasn't disengaging completely, then pivot ball snapped and fell out the bottom one day.

New clutch for me. Had a lot of other stuff being done around the same time so new clutch made sense anyway - thats how I justify it....

DS-ZILR Collaborator

DS-ZILR

Posted
Posted

must be the season for failing clutch boosters mine has a nice split through it! im after a new one anyone got a source for em? also heard you can use some model nevara clutch master cylinder and clutch booster dont suppose anyone has more info on this?

cheers crew

Dion

paulR32gtr Mentor

paulR32gtr

Posted
Posted
would you say it was worn regardless?

Nah the clutch was in good condition, was not too old and didn't go out in the usual way. It was either air in the fluid or the clutch fork & pivot were not aligned properly causing the crunch, and ultimately caused the pivot to fail.

600hp eh... yeah I imagine you would move through clutches fairly regularly. Better than gearboxes or driveshafts.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • joshuaho96
      Another Crank No start thread - r34 rb20 neo + t

      By joshuaho96 · Posted

      If you really don't want to touch anything you can try to trigger off the timing loop just to see if it's sparking semi-regularly. Don't trust it for actual timing measurements.
    • r34lad
      r34 starting problem

      By r34lad · Posted

      Also replace the fuel filter aswell today
    • r34lad
      r34 starting problem

      By r34lad · Posted

      Hey everyone, I have a r34 GTT s1, im having a problem with my skyline, ive let the car sit in the garage for the last couple of months and havent run it and ive gone to fire her up today and it cranks but doesnt fire, i have been having problems with it previously where it wouldnt start again after driving it around for a bit. It use to start fine on cold start ups but if you drove to the petrol station and fueled it up and went to go start it again, it would just crank and not fire untill you let it rest for a few hours, the car doesn't over heat it sits perfectly in the middle while driving when warmed up. Im thinking this problem has caught up maybe and now it just wont start at all. The car runs on e85, ive checked the e85 seems to be fine. I can hear the fuel priming before you go to start it and checked all my fuses and relays. List of things I replaced today - New battery - New sparkplugs - New Coolant temp sensor I was thinking about testing the CAS but from what ive seen online, if the CAS is cooked, the car will actually start up but then die instantly? as mine just doesn't fire at all. Does anyone have any idea or have encountered the same problems? thanks
    • MBS206
      Low oil pressure after WOT

      By MBS206 · Posted

      Modern reg stuff now, they'd have a wide input range which would push through a buck converter, it would need to be able to maintain voltage for cranking conditions (sub 9V at times). Likely runs something like an internal 6V rail, and then further voltage regulators depending on which circuit/area it is feeding. Modern voltage regs, like what I'm starting a new power supply design with at work, will let me run a 5V rail output, and as long as my input is equal to or greater than 5V, I have a 5V output. Except I'm not pushing a 5V rail in our system as I don't need one, we're setting up for a 3.8V rail. Our new design will allow me 6 to 60VDC input, and everything else doesn't care, even when I start pushing a few Amp outputs.   Realistically, the voltage drop off could be caused by a few things though, one could be literally the alternator is dieing, and hence charge power is dropping, which also means on a straight hard pull you're starting to send the battery flat... (Not that likely from a single couple of gear pull if the battery was fully charged). However, having earth issues, like stray earths not connected, or someone having put a ground loop in, will see the ECU appear to end up with lower voltage "input", mainly because the "ground" is no longer equivalent to battery negative. If they're comparing the input voltage using sensory ground for example, and sensor ground is what is in that ground loop, than the sensor output voltage will actually start to be reduced, when compared to battery ground... Yeah, ground wiring design can start to be a bitch... Also voltage going weird from inductive loads not being managed properly is another real bitch... Hence, why I asked above about how everything was wired in. If OP knows, and can post all of the actual connections from the ECU pin out, as well as what wires are joined where in the loom, which grounds from the ECU have ground points and where they are etc. Would help to see if there is a ground issue. The part I'd start with though, is putting a mechanical oil pressure gauge on to confirm the theory. Otherwise the next track day when the threshold is lowered could result in another of @Duncan favourite types of jokes... Knock knocks... Pretty sure this is what @GTSBoy is also self high fiving...  Is all great that we have a decent theory... But they need to prove it before relying on it...  
    • MBS206
      R32 GTST - 600KW+ RB28/CD009 Build

      By MBS206 · Posted

      When I worked at BlueScope Steel, we had an Ethernet network, with every switch setup with a duplicate switch. Even when looking at all the primary switches, they had duplicate links, there was then also duplicated links between the primary in section A, to the duplicate in section B. So for each location that had networking, there was 8 network links. This was all back around 2007. That setup caused sooooo many issues, as many of those links were fibre. The network guys ran everything with Spanning Tree Protocol. And then we had great joy... The FOC Transceivers were slowly dieing, but in an intermittent way. And a lot of the time as they started to die, they'd drop offline for about 30 seconds... Spanning Tree Protocol was requiring 45 seconds to "rewire" the network... And by the time it was mostly finished, it had to start again as the transceiver was back online... Queue entire production network being constantly spammed with the spanning tree protocol messages...   My god I do NOT miss working in huge environments like that!
×
×
  • Create New...