Jump to content
SAU Community

Recommended Posts

Guys this is going to sound really stupid, but how the hell do you get out of a driveway where both the road and the driveway are sloping in to one another ? Anyone have any special tricks to share ?

I just picked up two 2ft x 1ft panels of 10mm thick checkerplate that weigh in a tad on 15kgs each .... hopping in and out of the car is getting to be a bit of a bitch tho :(

Link to comment
https://www.sau.com.au/forums/topic/2735-new-place-driveway-assistance/
Share on other sites

Hehehe, yeh car is insured and on the road now :) hehehe, just working on a few things at the moment but other than that it's good to go :)

Just moved to a bigger place, and although the cement sounds like a good idea, it's in a block of 120 places sooooo it may be a little hard to pull off with people coming in / out all day ....

Taking it wide is what I would usually do and get the tyre in first then out, however I have dickheads who decide to park right next to the driveway (usually hanging 30cms into it) which makes taking the angle impossible ........ I guess my front bar is doommed !! :P

Guest Boxhead

i would steel some witches hats from you local council, then get a deck chair, do the cementing, and put the witches hats aorund it, set the deck ahir up for a couple of hours infront.. and if anyone walks up to you saying move, say, your doing them a favor, out of your own pocket, crap on about the cost.. then they will piss off

Jimbo,,,you are reversing down the driveway,,,yea. Birty's right,,,,get the angles happening buddy....and maybe get some pieces of wood,,like 1 x 4's,,,lay them in the gutter,,,where it meets the driveway and reverse over them,,,.Hide them in the garden, till your return.....

Neil

You could try asking the body corporate if you can do the cement thing, tell them you'll pay for it yourself, and if it's that quick-set stuff, it shouldn't put anyone out (or do it in the middle of the night when no one's trying to get in or out! hehe)

Is there anyone else in the complex with having the same problem?...maybe you could get them on-side too :P

I normally just drive up the footpath and use the next available driveway exit if I can't get out of the one i'm in.

So long as your car is at a legal height the driveway must be able to accomodate you so as Shell said, check with the body corporate and then get the concreting done, and if you are willign to pay they shouldn't have a problem accept that there will be no access for 3 days but its for a good cause (skyline) so they should understand.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I would paint match the whole thing to avoid unwanted attention  I had a similar bonnet, paint matched, on my old R33 GTST, but mine was a fibreglass jobbie made by Blitz in QLD, they work extremely well for radiator efficiency and under bonnet temps
    • Does anyone run this kit with factory plenum? Does the adapter and bosch tb fit under factory strut brace? I wanted to get this setup before going forward facing manifold. Thanks
    • small update time, after always wanting a "cool" looking bonnet for my car and always struggling to find one for the series 2 that i liked and wasn't an insane amount of money. Saw one i liked on RHDjapan from D-speed in Japan the price was very good for a carbon bonnet so good infact i was a little unsure how much i trusted it, decided to bite the bullet and with the help of jesse streeter in not long at all it was at my door. Once it was delivered i ran in from work and quickly unboxed it and to my surprise the quality was actually pretty good i quickly removed the old bonnet and placed on the new one to test it out and even the fitment wasnt too bad at all. Then decided to paint the little grille in the bonnet black to stop it sticking out so much.   I decided to not mess around with the hood latch and just install some aero catch hood pins, having never installed them before did some YouTube university classes and i was good to go. fair to say it is not a fun job at all from making brackets so the pins sit nicely and actually cutting through the bonnet but also being very scared of cutting the holes too big it took wayyyy longer than i would like to admit but finally got it there. Then it was time for a quick test drive to ensure the latches actually worked and thankfully the bonnet looked very stable. I still think paint matching the bonnet and leaving just the part that sticks up as carbon would help make it all look alot neater as im not sure how i feel about all that carbon on a very fridge white car but will leave it as is and see how i feel with time.  
    • I think it's bound to happen, you finally get it all perfect, and bam, something will happen. I took a while to get a Commodore rear quarter repaired where a P Plater clipped it. Two days after getting it back, Sarah wiped it out on a concrete pillar in an underground car park... This is why I take forever to repair them, it stretches how long until it gets bent again... 😛
    • Nah, not really responsible for that little fiasco, but I'm still pissed at myself for writing off my 86, or when I reversed my VX into a pole just before selling it, but, meh, 5hit happens to stuff, all it takes is a slight distraction, and life is full of distractions, and "dooh" moments   
×
×
  • Create New...