Wacky Dee Posted June 6, 2009 Share Posted June 6, 2009 Would like to polish my R34 (GTT) headlights with the Glassylite kit and also install a LED strip on the inside ... I read somewhere the only way to take the clear plastic cover is to "bake" the entire headlight in the oven so the plastic lets go ... Doesn't sound like something I really want to do ... has anyone else done it with an R34 here? How do you glue the clear plastic back on ? Any tips appreciated, Cheers Link to comment https://www.sau.com.au/forums/topic/273569-how-to-take-r34-headlights-apart/ Share on other sites More sharing options...
wisey18 Posted June 7, 2009 Share Posted June 7, 2009 Yeh, you bake them in an oven. Not sure on the temps or amount of time you have them in for. You do the same to put the headlights back together. Get the glue hot then just stick them together and wait for it to dry. Link to comment https://www.sau.com.au/forums/topic/273569-how-to-take-r34-headlights-apart/#findComment-4642433 Share on other sites More sharing options...
Silver_GT Posted June 8, 2009 Share Posted June 8, 2009 going to do mine one of these days... i did it to my pulsar ones, to paint the lens surround black, but they had glass lenses, id assume the same method however. oven on about 80-90 degrees, pop em in on a tray with baking paper on there, after 2-3 mins pull em out, see if theyre hot (ALMOST too hot to hang on to) if not giv em another minute and keep checking, then you want to GENTLY pry the lense off. just do it a little at a time, if its starting the get difficult, pop them back in the oven. its best to take your time with this, you dont wanna crack your lense from pulling too hard! mini disclaimer: i take no responsibility for any damage that occurs from doing this, im not an expert Link to comment https://www.sau.com.au/forums/topic/273569-how-to-take-r34-headlights-apart/#findComment-4643666 Share on other sites More sharing options...
chrisR34GTT Posted June 9, 2009 Share Posted June 9, 2009 Gave this a half hearted effort last night and wasn't sure where to start prying the lens off from.. and should the seal be sticky or just gummy? this sucks I have moisture on the inside of the lens and it looks shiat with the headlights on help me.... Link to comment https://www.sau.com.au/forums/topic/273569-how-to-take-r34-headlights-apart/#findComment-4645843 Share on other sites More sharing options...
GTR-N1 Posted June 9, 2009 Share Posted June 9, 2009 Gave this a half hearted effort last night and wasn't sure where to start prying the lens off from.. and should the seal be sticky or just gummy? this sucks I have moisture on the inside of the lens and it looks shiat with the headlights on help me.... You've brought up a good point! After separating parts of your headlights, you'll need to re-seal them again UNDER LOW HUMIDITY CONDITIONS or you'll end up with moisture on the inside. But if you have a type of lens that is not sealed from outside conditions, you can store the lens in a sealed plastic bag WITH RICE GRAINS OR SILICA GEL PACKS (obtained from medicine bottles) until the moisture disappears. Rice grains and silica gel act as dessicants (to absorb surrounding water). Link to comment https://www.sau.com.au/forums/topic/273569-how-to-take-r34-headlights-apart/#findComment-4646038 Share on other sites More sharing options...
ylwgtr2 Posted June 9, 2009 Share Posted June 9, 2009 we do them all the time here at work with motorbike headlamps.....you can just put it in front of a heater or use a heatgun in one section first,then when it starts to open up just follow the opening...its easy Link to comment https://www.sau.com.au/forums/topic/273569-how-to-take-r34-headlights-apart/#findComment-4646120 Share on other sites More sharing options...
Wacky Dee Posted June 9, 2009 Author Share Posted June 9, 2009 can anyone recommend some type of sealant to use to run along the edges after putting the lense back on? Something like sikaflex automotive ..would that be a bad idea? Just to ensure a good seal .. Link to comment https://www.sau.com.au/forums/topic/273569-how-to-take-r34-headlights-apart/#findComment-4646221 Share on other sites More sharing options...
cosmic starz Posted June 9, 2009 Share Posted June 9, 2009 <br />can anyone recommend some type of sealant to use to run along the edges after putting the lense back on? Something like sikaflex automotive ..would that be a bad idea? Just to ensure a good seal ..<br /> <br /><br /><br />---------------------------------------------------------- You can buy mastic in a tube for a few dollars (any auto supplier should stock it) - a small tube should be plenty- its the stuff that was used to seal windscreens before the latest glue-on type windscreens were introduced - it is a very good sealer does not age harden and easy to apply - but maybe someone else can suggest other options Re a quick short-term fix for getting the moisture out of the h/l when its in situ on car all you need do is take out off the outer circular plastic seal, then the bulb holder and the insdie of the h/l is now exposed and you can use compressed air or any thing similar to blow away any moisture- until you are ready to do the long-term fix. Link to comment https://www.sau.com.au/forums/topic/273569-how-to-take-r34-headlights-apart/#findComment-4646568 Share on other sites More sharing options...
ylwgtr2 Posted June 9, 2009 Share Posted June 9, 2009 you can buy the sealer from nissan....its the same stuff used on the tail lamps....its made by bostik Link to comment https://www.sau.com.au/forums/topic/273569-how-to-take-r34-headlights-apart/#findComment-4646577 Share on other sites More sharing options...
chrisR34GTT Posted June 10, 2009 Share Posted June 10, 2009 we do them all the time here at work with motorbike headlamps.....you can just put it in front of a heater or use a heatgun in one section first,then when it starts to open up just follow the opening...its easy Location and how much?? Seriously this is causing me some heartache... I have discovered that it is not only moisture on the inside but also oxidation similiar to that found on the outside of the lens, cause: the two housing brackets on top of the h/l cracked off exposing the internal of the h/l.. I can't really afford a new factory xenon either Link to comment https://www.sau.com.au/forums/topic/273569-how-to-take-r34-headlights-apart/#findComment-4646750 Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now