Jump to content
SAU Community

Fs: Rb20det Full Motor + Loom + Gearbox

KaiShin
 Share

Recommended Posts

KaiShin Enthusiast

KaiShin

Posted
Posted (edited)

As the title states...

Pretty much selling a full conversion RB20DET...

Includes:

Full RB20DET motor including turbo, inlet plenum, dump pipe, coil packs etc (No Ancillaries)

Full engine loom and coilpack loom (will need to modify or purchase a starter loom)

ECU

Flywheel

RB20DET gearbox (minus shifter)

I can also include ancillaries at an extra cost.

Looking for $1100 for everything w/out ancillaries.

The only thing I can see wrong is the harmonic balancer has been damaged but this is cheapely replaced.

Motor has 120k klms on it, and came out of a running car that was in a front end accident.

I also have R32 mounts to go with the engine if needed.

Was going to put this into my Laurel however have decided on RB25 or 1UZFE.

Located - Brisbane Nothside

Will provide pics tonight.

Edited by KaiShin
Link to comment
https://www.sau.com.au/forums/topic/274033-fs-rb20det-full-motor-loom-gearbox/
Share on other sites
KaiShin Enthusiast

KaiShin

Posted
  • Author
Posted

All PM's replied too again.

I am happy to seperate the motor from gearbox, not really interested in pulling the motor apart unless I have buyers to get me the funds I need.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Watermouse
      Hypergear Turbochargers and High flow Services Development thread

      By Watermouse · Posted

      That’s a beautiful setup Tao, Have u done any development with the new Turbosmart 40mm electronic straight gate, especially in this G30 configuration?
    • Dose Pipe Sutututu
      Neil's R33 Gts-t Build

      By Dose Pipe Sutututu · Posted

      Let's hope that's not a copy pump either. There were so many copies of them back in the day.
    • The Bogan
      NC MX5

      By The Bogan · Posted

      Damn it, I was at work last night, and stayed in a room there during the storm with the car outside, but undercover, I just went downstairs and well....there was a large steel locker that has come from some place last night, it wasn't anywhere I could see yesterday, and yeap, it landed on the fraking car....of course it did..... LOL So, I'll need to take it back for paint and panel, luckily it was only the boot that took the hit, so it could have been worse Serves me right for staying at work and getting on the cans with some of the boys
    • The Bogan
      NC MX5

      By The Bogan · Posted

      Yeah, really happy with how it all turned out As for aftermarket lip, nah, I'm not really a fan for practically reasons on a street car that gets driven everywhere  I did have the full lower kit on my 2015 STI, but found the front lip scrapped alot, even at stock 4x4ish ride height As the NC sits now, with the lowest point of the car at 110mm, so just legal, some steep driveways and steep speed humps will still "just" scrap those little plastic OEM air dam thingies on the undertray just before the front wheels
    • Dose Pipe Sutututu
      Hypergear Turbochargers and High flow Services Development thread

      By Dose Pipe Sutututu · Posted

      Here's one I help build and tuned a decade ago, Garrett  GTX3071R Gen 1, T3 twin scroll 0.83 rear housing. Went from larger 272 cams down to smaller Tomei Poncams to help with the low end. S13 non VCT motor. Car was purpose built for the track, hence low down was the focus. Note the actual dyno chart shows lower boost, however the EBC and boost gauge showed 1.9Bar (Ignore the torque, I was young and didn't know how to set derived torque)  
×
×
  • Create New...