Jump to content
SAU Community

Check Engine Light, Car Won't Start

Coxie

By Coxie,
in Engines & Forced Induction

 Share

Recommended Posts

Coxie Contributor

Coxie

Posted
Posted

Ok so I had the ecu out just to see whether it was a completely stock ecu or remapped etc, and when i plugged it in again, they car started and ran for about 1 minute then died and hasn't started since, when I turn the ignition on the check engine light stays on and won't go out like it should do. When i put the ecu into diagnostic mode it flashes code 55 meaning everything should be fine? but still the car won't start. I can not smell any fuel in the exhaust after cranking, but can hear the fuel pump prime when i turn ignition on... so maybe something to do with the injectors? or could it be the airflow meter? the ecu has a bit of dodgy wiring behind it where something has been tapped into it in the past but everything looks like it's connected to where it should be so I don't know whats causing the problem? Any ideas guys...?

Link to comment
https://www.sau.com.au/forums/topic/274351-check-engine-light-car-wont-start/
Share on other sites
cosmic starz Collaborator

cosmic starz

Posted
Posted

If I wrere you I would firstly only look at the things you touched and not jump to other conclusions yet - why not pull out the ecu again and make sure all pins/connectors are OK - re-connect evrything and try a start again - no doubt others will offer suggestions also

Coxie Contributor

Coxie

Posted
  • Author
Posted

funkymonkey - yeah starter motor was working, engine was definately cranking over.

lachlan33 - yeah there was a wire that has a joiner in it that came apart but like i mentioned earlier in the thread i'd already checked all the connections.

Problem was th blown fuse, not sure how or why it blew but guess it was just doing it's job, starting fine now.

Thanks guys

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Trilbyte
      RB25 S2 Idles but doesn't want to rev

      By Trilbyte · Posted

      No intention of driving the car the way it's set up now, just wanting to make sure I haven't made any mistakes along the way so that the tune can go smoothly, I don't want to waste anyone's time with stupid issues. And of course I intend to get it towed to the dyno in a completed state 😅 I have the base fuel pressure with the vacuum disconnected set at about 40psi, which I believe is at least relatively close to stock fuel pressure, maybe I'll have a fiddle with the reg and see what happens. For all I know I could be wasting my time with this and I should just plumb it in and see what the tuner reckons. I just find it a bit strange that it seems to be under so much load just free revving, but maybe that's just a result of the turbo slowing down the exhaust gasses and making a restriction in the flow, with no boost to compensate.
    • The Bogan
      MLR's Bogan cruise ship

      By The Bogan · Posted

      The boy just hit up google translate and it worked a treat, he said step one was "please urinate with precision and elegance", he then sent me the correct translation  I get some new loctite for the small fixtures tomorrow and get some "dort" going after that 🤣
    • Kinkstaah
      RB25 S2 Idles but doesn't want to rev

      By Kinkstaah · Posted

      Right, so is the fuel pressure the same as it was previously? If not, well, it's not going to work well. I can understand the theory I assume you are going for, which is: "Run it N/A, and if I have the original AFM, and same amount of fuel and intake air as previously, the fact there's a turbo in my exhaust should still make it run" Which it... might? Provided you don't actually change how much air or fuel is going into the car.. or getting out. But if you have changed that, all bets are off. What is the purpose to even have the car run this way? To get it to a tuner? And if the goal is to limp it to a tuner, you're still going to what - plumb up a whole intercooler system and new intake in the parking lot out front before your tune......?
    • Trilbyte
      RB25 S2 Idles but doesn't want to rev

      By Trilbyte · Posted

      Haha yea it's a bit of a weird setup at the moment, just wanted to make sure I sorted out any headaches before dyno day. At the moment I've changed the exhaust manifold, turbo and downpipe, 460lph fuel pump and rising rate reg as well as the previously mentioned headstuds and gasket. The nistune was already mapped for the car as it was and drove around for a few months no worries. The plan is to run flex fuel hence the big pump, which I've wired direct to the battery through a relay to avoid voltage issues.
    • Kinkstaah
      RB25 S2 Idles but doesn't want to rev

      By Kinkstaah · Posted

      Um. Was the ECU the same as the one previously there? I know R33's needed R32 GTST ECU's or other tomfoolery to run Nistune. This is such a wild setup. Most people would plumb in the turbo then not drive the car (i.e tow it to a tuner). What's actually changed since it last ran?
×
×
  • Create New...