Jump to content
SAU Community

LED Parkers

Henros

By Henros,
in General Automotive Discussion

 Share

Recommended Posts

Henros Enthusiast

Henros

Posted
  • Author
Posted

Hey guys,

Thanks for the replies. They're not off the shelf replacements, I made them myself. Each "bulb" is made up of six 5mm white LEDs, in 2 strings of 3. I added a dropping resistor (68 ohm) for current limiting and a diode (IN4004) for reverse polarity and transient high voltage protection. The whole package was soldered onto a very small PCB and plugged into the original socket. The only downside is that LEDs have a much narrower light cone, so that the light doesn't look as spread out as the original bulb, but the colour is a lot nicer.

Cheers.

Link to comment
https://www.sau.com.au/forums/topic/27452-led-parkers/#findComment-576420
Share on other sites
sewid Grand Master

sewid

Posted
Posted
Originally posted by Henros

Hey guys,

Thanks for the replies. They're not off the shelf replacements, I made them myself. Each "bulb" is made up of six 5mm white LEDs, in 2 strings of 3. I added a dropping resistor (68 ohm) for current limiting and a diode (IN4004) for reverse polarity and transient high voltage protection. The whole package was soldered onto a very small PCB and plugged into the original socket. The only downside is that LEDs have a much narrower light cone, so that the light doesn't look as spread out as the original bulb, but the colour is a lot nicer.

Cheers.

To diffuse the light output of 5mm LED's you can sand down the "lens" portion of the top of the LED.

Try it out and see if it improves the light spread.

Link to comment
https://www.sau.com.au/forums/topic/27452-led-parkers/#findComment-576571
Share on other sites
Henros Enthusiast

Henros

Posted
  • Author
Posted

Here it goes guys, my first step by step guide

1. Remove the parkers from the car by disconnecting the wiring and twisting the sockets anticlockwise 90 degrees. This step is sure to be accompanied by much swearing the cutting yourself due to the awkward position and lack of clearance. Persistence is the key and may the force be with you.

2. Remove the 5W wedge lamp and measure the diameter of the socket opening (round end). I can't remeber the exact measurement but it should be around 13 to 14 mm. Cut either a blank PCB (printed circuit board) or a prototype strip board into a circle with the same diameter. You need 2 of those. The PCB approach is neater but needs etching to produce the pattern. The prototype board has pre-existing copper tracks but you're gonna have to work out the wiring pattern according to the circuit diagram yourself, but that shoudn't be hard. You can even use an insulating material without and copper tracks and just solder the component legs directly to each other. The role of the circular board, whatever you decide to use, is to provide a physical and electrical mounting platform for the electronic components. I will describe the PCB approach here.

3. The circuit diagram is given below (see LEDParkerCircuit.gif). As you can see, the LEDs are connected in a series-parallel configuration to minimise electrical dissipation. The resistor provides current limiting and the diode provides protection against reverse polarity and transient high voltages. I have used a resistor value which will drive the LEDs at 20 mA when the engine is on (13.8V). If you want to increase the brightness, you can reduce the value a bit, but I wouldn't go any lower than 51 ohms (which is 30 mA at 13.8V).

4. The PCB pattern was designed according to the circuit diagram, see diagram (LEDParkerPCB.jpg). Replicate the pattern with a permanent marker and let dry. Once dry, the PCB can be etched in either a iron III chloride or ammonium persulphate solution. The solutions are made by desolving appropriate amounts of the chemical powder in water. Read the instructions accompanying the chemicals. The ammonium persulphate solution need to be warm to work, so use hot water.

5. After etching, rinse the PCB in fresh water and clean off the permanent marker with metho or mineral turps. Rinse in water again. Drill holes in the PCB as shown in the diagram below (LEDParkerPCBDrilled.jpg).

6. Insert LEDs onto the board from the non-copper side and solder in place as shown in the diagram (LEDParkerPCBLayout.jpg). The resistor and diode are solder only at one end on the copper side. They also fuction as electrical contacts. See

diagram (LEDParkerPCBSoldered.jpg). Note that I have used 2 resistor in parallel, that's because I didn't have any 68 ohm resistors at the time.

7. Bend the leg on the other side of the resistor and diode and apply liberal amounts of solder to they fit snuggly in the socket contacts.

8. Plug the LED module into the socket and test it on the car. If the LEDs do not light up, reverse the pins and try again. Once you'll satisfied, secure the PCB to the top of the socket with a little bit of superglue. This is to make sure that it doesn't get shaken loose by vibrations. The finished product is shown in LEDParkerAssembly.jpg

9. Reinstall the parkers and wiring. Enjoy your new blueish white parkers!

Disclaimer: I take no responsiblity for anything that happens to you or your car should you give this a try.

Cheers.

Link to comment
https://www.sau.com.au/forums/topic/27452-led-parkers/#findComment-577362
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      The old manifold was quite under the GTR strut brace.  The new manifold is quite [unknown] the GTR strut brace. The GTR strut brace was needed to clear the bonnet vents. The Old strut brace will almost certainly clear the new manifold, but not the bonnet vents. The old strut brace will almost certainly clear the new manifold, and the new bonnet without vents. But I am hoping the GTR strut brace clears the new manifold :p
    • The Bogan
      Mistakes were made, my R34 Story

      By The Bogan · Posted

      Bonnet clearance?
    • joshuaho96
      Magnetic Drain Plug Snapped in Half

      By joshuaho96 · Posted

      On the bright side, at least you knew that it happened and remedied before anything happened. A friend of mine just took his Fiat 124 to a shop for an oil change and they didn't tighten the oil filter housing properly. 4.5 quarts spewed out and even after refilling + tightening the cap the engine has a tick now.
    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      So, more pain. The FAST manifold is a little larger than the stocker. This is problematic because there really wasn't much clearance to begin with, so going from 'barely enough' well into 'no' is sad based on the external dimensions of the thing, even though where it bolts to the head is the same. Result is the fuel rails sit a good 25mm higher, and this is a bit of an issue with the wiring that runs behind the motor, and the fuel lines, and everything else. When pushing the manifold on, it required a huge amount of force to crush wiring looms to fit it, sensors like the MAP sensor are about 1mm from the firewall, and the FPR just has to bend ABS lines to be forced into place. After some brainstorming and some sad drinking, the loom for some reason ran from the grommet behind the ABS sensor, then to the driver side head, then back to the passenger side head. So all of this was pulled back and stripped, a few wires cut and rejoined, so that the 'branch' was now on the passenger side's head as below: Before you basically couldn't see anything behind the driver head. This is much improved! The MAP sensor is now pointing up (instead of at the firewall) Brackets have been made up for the rail. The rails are for a LS1, the manifold is designed around a LS2 as it's base. Which of course has slightly different bracketry and water pump clearance, hence the mods people need to do. Should be hopefully mounted tonight. I spent money on a new FPR that is slightly more compact than my Turbosmart FPR1200. The gauge has also been moved to the rail. There's also apparently an ORB to AN Union instead of the adapter, because the ~25mm of the current adapter is going to make the difference. Provided this all goes together and arrives today, it'll be the totally not stressful attempt to start it.
    • GTSBoy
      Finding E-30 & E-85 in Sydney

      By GTSBoy · Posted

      This seems like a pointless exercise. There is no E30 availability. Ongoing availability of E85 should not be assumed. Flex-fuel is the only sensible approach, so you can use E85 when and where you can get it, 98 when that's al you can get, and anything in between as you fill it up and drain it down. And if that means replacing the pumps, fitting a flex capable sensor/ECU/whatever has to be done to these Renault shitboxen, then.....so be it?
×
×
  • Create New...