Jump to content
SAU Community

Recommended Posts

I've just tried some Carbotech XP12 pads (for track work) and to be honest i wasnt overly impressed. Plus they squeal like there is no tomorrow (after a few days of light road use, like most track pads i guess) and it's a major PITA - so i've just put the stocker pads back on (super quiet again, thank god).

Anyway has anyone priced the stocker pads? From Nissan it's probably a bloody fortune, so i am not going to bother asking. But, perhaps someone has sourced them elsewhere? They are Brembo pads right?

Link to comment
https://www.sau.com.au/forums/topic/274657-r35-stocker-brake-pads/
Share on other sites

you're right, they are a fortune I can't remember exactly but it was around $1000 per axle set. look at endless or project mu. they both make great pads and should be more reasonable $$ wise. they do everything from nice quiet, low dust street pads to dusty as fk, hard when cold, agressive, 800C track pads.

that would be about right for one axle set. ie both front calipers (4 pads total). they never sell just 1 calipers worth and PMU sometimes offer full sets too (ie all pads front and rear, but $600 would be a bargain for a 35).

I picked up some Ferodo DS2500 pads for the front end yesterday, $495.

Also got some new AP rotors for $825ea too, curved slots.

I think this combo (Ferodo pads + AP rotors) will be very close to stocker setup, with the discs certainly better, but we'll see.

Out of interest, has anyone got a price from Nissan on stocker rotors or pads yet?

I assume it will be in the order of 2x the cost? - i am not even going to ask!

  LSX-438 said:
I picked up some Ferodo DS2500 pads for the front end yesterday, $495.

Also got some new AP rotors for $825ea too, curved slots.

I think this combo (Ferodo pads + AP rotors) will be very close to stocker setup, with the discs certainly better, but we'll see.

Out of interest, has anyone got a price from Nissan on stocker rotors or pads yet?

I assume it will be in the order of 2x the cost? - i am not even going to ask!

How are you? I hope all is well. I hope you are sitting down when you hear the OEM brake prices...OEM pads are $725 USD for front and $483 USD for the rear. The rotors (front or rear) are $1081 USD. Crazy expensive!

We offer a 'track brake package' with front and rear XP12 pads (noisy but they bite well...we can also exchange these for any other pad we offer such as Ferodo, etc.), front and rear AP Racing J-hook rotors, T1R V2 stainless steel braided brake lines, and 2x bottles of Motul RBF600 fluid for $3000 USD, with international orders getting a $75 credit toward shipping costs:

https://www.speedforsale.com/nissangtrparts...jjgv0cp0gfi5g94

  John D said:
Duncan

Front pads about $2000 and the rotors about $1700 each for gen brem, I mean nissan. :)

That's a pity they are so expensive. I actually liked the stocker pad/rotor combination, better than i thought it would be anyway, even for the circuit i found them fine. Since i've used aftermarket pads the stocker rotors have started to crack though. Higher friction & more heat, to be expected i suppose.

Thanks for the prices guys, hopefully the price for the stocker parts will come down in future.

  • 1 month later...
  Priestley said:
I found a set of Project MU street spec pads for about $600. Does this sound right for a front set (both sides) or just one side?

Hi Priestley,

Which model of Project Mu pads were you quoted $600 for ? Was that price for front and rear pads (ie all 4 corners of the car) or front pads only ?

Project Mu makes 3 models of street / sports pads for the R35 - the TYPE NS, B-SPEC and the TYPE HC+.

Australian prices for the R35 for Type NS front pads is AU$390. Rear pads for the R35 start at AU$249 for the NS pads.

So if you were quoted $600 for NS front and NS rear pads that's about $39 below standard Australian pricing.

We have a page on our website explaining the differences between each Project Mu pad compound available for the R35 (street / sports and competition pads, with temperature and Friction Coefficient specs) here ...

http://www.tunersgroup.com/Online_Store/r35_pads.html

- The Tuners Group

FWIW guys i have been using Ferodo DS2500 pads, about $490 (fronts) and $440 (rears) - i think these are the closest to stocker pads you will find. I've run them at the track a few times are they are very comparable to stocker performance, progressive feel and noise (not really squeaky at all). Send me a PM if you want a contact to buy these.

  • 4 months later...

Just in case you need the parts #'s here are some I have parted out with. I know this is an old thread

also here are the caliper dust boot part #'s

Front caliper is a 6piston.

Front 20.9716.01 F

Rear is a 4 piston caliper. ® 20.9717.07

Dust boots PN # 20-4872-41

Front:(dia.)

20487244 = 36mm

20487243 = 34mm

20487241 = 30mm

Rear:

20487243 = 34mm

20487241 = 30mm

DSCN5240.jpg

Edited by racer98
  • 1 month later...
  • 1 month later...

thread mining again.

What have been peoples experiences with R35 pads?

I have tried Carbotech xp12's (great bite but squealed like a cop on the street) DS2500's (about the same as stocker pads) Hawk's (did not sweep the entire rotor, 10mm less!) and MX72's (not as much bite as the xp12's but virtually squeal free on the street, and kind to rotors).

Anyone tried the project mu HC+ in their r35? if so, did they squeal? how did they perform?

they seem "cheap" about $800 for a full set.

  • 2 weeks later...
  • 3 weeks later...
  • 2 weeks later...

wow those nissan prices are criminal.

Anyway i have been using Endless ccRg the last couple of track days; they seem to have the street manners of the mx72's but with more bite. They feel awesome. I think about $700 to $800 (for the fronts AND backs, yes total cost for four corners)

No squeal yet.

I think they work up to about 800*c so less fade too.

Edited by LSX-438

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I'd say the easiest way is, pick up a extended and baffled sump with fittings already welded on. Here is an example, it has 3 x -10 fittings  https://shop.maatouksracing.com.au/products/rb-extended-and-baffled-sump
    • hey OP can you remind me what the actual question was, I got sidetracked at V12. Do you have an turbo oil return leak and an unidentified coolant leak? The factory oil returns are terrible design; short, rubber and expensive to replace. They are very common to fail and a pain to replace because they are so short. Still, they are available new if you want to replace both last time I checked. For the coolant leak, any competent mechanic should be able to do a pressure test; that should show up where the leak is. It is almost certainly one of the billion 30 year old rubber lines which are now brittle as hell, you engine will be fine.
    • From the OP's description, sounds to me like the TCU is in 'limp home' mode --- that is, no actuation power to shift solenoids, and the EPC valve is shut (full line pressure). This effectively sticks the box in 3rd gear, with as much line pressure as possible, to try hold the high clutch clamped shut....and so you get woeful acceleration and don't feel any shifts (because they're not happening). If you don't have Consult or some other scanner to interrogate the TCU itself, you can test with a multimeter to see if it's in limp home mode....ie; stick it in D with engine at idle (hold vehicle with hand/foot brake), and measure the voltage at the TCU feeding shift solenoids A & B -- both should be ON (battery voltage). If they are energized at the TCU, you can unplug the harness from the TCU, and check resistance down through the wiring to the solenoids themselves -- you should see about 20ohms on each coil --- if you do, you can presume the wiring to shift solenoids is OK -- if both measure open circuit, you have to check intermediate connectors in the loom down to the gearbox (and the gearbox connector itself), and check the shift solenoid resistance at the gearbox connector itself --- if the shift solenoids test open circuit here, problem is in the box (ether the solenoids or wiring to them is bad). If you get no voltage at TCU connector for the shift solenoids (and the solenoids/wiring test OK), check powers/grounds to the TCU itself --- if they're ok, it suggests the TCU is the culprit (and you'd need to interrogate it if possible, to find out why it's behaving badly)... 
    • Hey mate give Autotechnica a go, I recently got some Comfort PUs and rails from them, they're comfy and look great highly recommended! https://www.autotecnica.com.au/part-finder/nissan/skyline/r32/
    • Honestly, for a daily I would gladly rock a Camry. The more disposable the better. People drive horribly out here and road conditions are awful.
×
×
  • Create New...