Jump to content
SAU Community

Recommended Posts

So tonight after work I decided to clean my engine bay. All well and good, did it while car was running no problems.... I finish up start driving home and just briefly gave it a squirt and I got the dreaded miss... No worries I thought, it must be due to the engine clean I had just done.

I get about 3 streets away from my place and the misfire starts on low throttle, I pull up into my driveway and the car sounds as if it is running on 5 cylinders now...

I'll leave it overnight and see if there might have been some excess water that may have dropped into cylinders. Would anything else cause this though other than "your coilpacks are hammered" or "change your plugs"...

It must be related to the clean I just did, but if I have damaged anything in the process what should I be looking at?

Cheers.

Link to comment
https://www.sau.com.au/forums/topic/274909-not-another-misfire-thread/
Share on other sites

it will more than likely be due to moisture as guilt-toy said. first look for any pools of water around the plugs. if there is use a compressor to blow the water out or tissues to mop it up if you don't have a compressor. do this before removing the plugs.

then take the plugs out and give them a wipe down with tissues, and do the same with the coils. stick it all back together and see how it goes

pull the coilpacks out. when i did my engine bay. i covered all the electrical components. still managed to get water into my coilpacks. on some cylinders the water completed covered the spark plugs. didnt take long to clear out and is also good as you can check that the coilpacks and plugs are in decent condition.

Was planning on doing your suggestions tomm. Weird thing is though, I started it today no problem until car got warm and I opened throttle a bit.. Misfire again even on idle.. Looks like a trip to burson tomm. For plugs and can of compressed air.. Will let you know how it all goes. Thanks for the suggestions.

Was planning on doing your suggestions tomm. Weird thing is though, I started it today no problem until car got warm and I opened throttle a bit.. Misfire again even on idle.. Looks like a trip to burson tomm. For plugs and can of compressed air.. Will let you know how it all goes. Thanks for the suggestions.

I had a misfire problem for the past month after installing a new ECU, cam gears and injectors (R32 GTR). We replaced ignitor, coils, plugs, ECU - checked fuel filter, fuel pump, earthings etc etc - remapped fuel also. After doing this (all on Dyno etc) we still couldnt resolve it.

IT ENDED UP BEING THE EXHAUST MANIFOLD GASKET!!!

If you get nowhere on the electrics try to listen out for a hissing noise around the exhaust manifold.

Was planning on doing your suggestions tomm. Weird thing is though, I started it today no problem until car got warm and I opened throttle a bit.. Misfire again even on idle.. Looks like a trip to burson tomm. For plugs and can of compressed air.. Will let you know how it all goes. Thanks for the suggestions.

this is due to the extra load once you get on the gas. very few missfires happen at low load

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The boot notch on the GK Tech rods is different to OEM yes. You'll find a solution. They are a good rod, I have used many of them for various setups, and no they are not ' just for drift cars', they are fine as an OEM replacement. Same goes for the tie rod ends although I found they transmitted a huge amount of NVH a normal balljoint masks, making it feel like there was something loose or knocking, even though there wasn't. If you used the same pieces on each side, no reason one angle should be different to the other side. Have you checked ride heights/measured the angles? Or just visual? Your alignment will be massively out of whack yes. Up to you; it is worth taking the time to learn wheel alignments and do it yourself. I have never had better wheel alignments and I haven't taken my car to a shop for, dunno...many many years. Spend a few hundred on equipment, do alot of research via online articles, youtube vids, and "trial and error" on setups. Eg, set it with too much toe-out, toe-in, too much or little caster, drive the same stretch of awesome twisty mountain road each time, learn how they feel and how the car's handling has reacted to your changes.
    • Won鈥檛 be hard to beat them. 馃ぃ Farken sponge cakes!
    • Nah I did not will have to another time. I only installed a blitz return flow FMIC probably 1000kms ago. When I took the old piping off there was basically no oil in piping. At this stage it has to be valve stem seals. When I roll down a big hill in gear and then throttle down the bottom, I get the same puff of smoke.
    • I believe when they added coolant to cool the turbo it negated the need for turbo timers as water continues to flow even when the engine is shut off I forget the actual terminology, I'll just say the coolant "percolates" through the turbo which stops the oil cooking itself to death  Well....that's how I see it, as all the plant at work that has coolant lines to the turbo can be shut down straight away, whereas the older plant with only oil feed to the turbo you need to idle it for a few minutes
  • Create New...