Jump to content
SAU Community

Rb 26 Rwd Set Up Motor/ N1 Turbos

adam Foster
 Share

Recommended Posts

adam Foster Mentor

adam Foster

Posted
Posted

rb 26 motor rebuilt in sep 08 done 3500km, rebuild cost to much total cost still unknown. involved was forged pistons and rods arp head studs n1 oil and water pump. full head service copper head gasket built to handle power.

motor asking $7500

gearbox and exceed cluch near wornout $1100

r32 n1 nismo turbos back one blown oil seal needs rebuild offers

and have complete r33 s1 car

if motor sells will be stipping car

will make deal

or full car for $11000 no offers bodys ruff. has rego till oct 09

located near newcastle call me on 0411672105 any questions or ideas

Link to comment
https://www.sau.com.au/forums/topic/274980-rb-26-rwd-set-up-motor-n1-turbos/
Share on other sites
adam Foster Mentor

adam Foster

Posted
  • Author
Posted

hi guys the car has coil overs big exhaust for dumps back. was my drift car project nearlly got there. body is half sandered back. gtr dash sard fuel reg. its hard for me to get on the net so if anybody is interested please text me on 0411672105 and i will call. can send photos by phone.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • thatjawncrazy
      Another "where do these lines and plugs go" RB25DET question

      By thatjawncrazy · Posted

      GTSboy, thank you again. i’ve been reading all the other SAU RB25 vacuum line threads and you have the utmost patience for people asking “where do my vacuum lines go”. it’s appreciated. i did also enlist a few other RB guys local to me.  i would like to run 5 to 4. turbo pressure side to wastegate actuator. i would like to run 3 to 1. power steering air valve line to intercooler outlet. (this is how it was previously). i was told 2 is the bleed port for the boost solenoid - which i’m not running - so should be capped.   anyone see any problems with that?    
    • Kinkstaah
      Ethanol Content Sensor - Always at 11%?

      By Kinkstaah · Posted

      So yes. All of them. Something like 98% of all fuel in the USA has 10% ethanol: https://afdc.energy.gov/fuels/ethanol-fuel-basics It's labelled as like, AKI, 87, 91, 93 with an E10 or E5 or E15 label on the pump. At a certain point, it's not just "E10" instead of 91. It is 91, 95, 98, and all of them have 10% Ethanol in them. You can also get E85 and E30 which is why you do see some people rolling around with E30 tunes in them.
    • Stringycheese
      Blue slip

      By Stringycheese · Posted

      Thanks for the response. This is an 04 EP3 Type R. JDM spec. Fairly certain they're just basic BC racing coils. I do plan to keep as the ride quality on stock I've been told is pretty meh given Sydney roads. If I were to go down that avenue, does NSW require them to be a certain spec (close to original) etc?
    • PranK
      Blue slip

      By PranK · Posted

      Should have asked what is the car?
    • PranK
      Blue slip

      By PranK · Posted

      I've had two super conflicting experiences with blue slips. My 30 year old E39 waltzed through with no issues but my brother in law was knocked back on 12 y/o 3 series due to wiper blades and some cracking in a control arm bush.  What kind of coil overs? Do you want to keep them after?  If it was me I'd get some dirt cheap shocks and springs from eBay or scumtree. Not ideal but will get you over the line and might even be less than $1k.
×
×
  • Create New...