Jump to content
SAU Community

Recommended Posts

  • Replies 70
  • Created
  • Last Reply

Top Posters In This Topic

Rim width must not exceed the maximum rim width specified by the manufacturer by more than 25mm (1") (for passenger vehicles manufactured after 1st January 1973, the manufacturers rim width shall be taken as that specified on the tyre placard).

In any event, rim width shall not exceed 177.8 mm (7") unless specified by the manufacturer as standard equipment for the vehicle in question. No increase in rim width is permitted for vehicles fitted with original equipment rims in excess of 177.8 mm (7") width.

The tyre to rim fitment must be in accordance with the Tyre and Rim Association Manual.

All wheels must be the same size, profile and bolt pattern.

Thats probabbly everything that applies Douse.

Rim width must not exceed the maximum rim width specified by the manufacturer by more than 25mm (1") (for passenger vehicles manufactured after 1st January 1973, the manufacturers rim width shall be taken as that specified on the tyre placard).

In any event, rim width shall not exceed 177.8 mm (7") unless specified by the manufacturer as standard equipment for the vehicle in question. No increase in rim width is permitted for vehicles fitted with original equipment rims in excess of 177.8 mm (7") width.

The tyre to rim fitment must be in accordance with the Tyre and Rim Association Manual.

All wheels must be the same size, profile and bolt pattern.

Thats probabbly everything that applies Douse.

wow.. when did that come into affect?

Rim width must not exceed the maximum rim width specified by the manufacturer by more than 25mm (1") (for passenger vehicles manufactured after 1st January 1973, the manufacturers rim width shall be taken as that specified on the tyre placard).

In any event, rim width shall not exceed 177.8 mm (7") unless specified by the manufacturer as standard equipment for the vehicle in question. No increase in rim width is permitted for vehicles fitted with original equipment rims in excess of 177.8 mm (7") width.

The tyre to rim fitment must be in accordance with the Tyre and Rim Association Manual.

All wheels must be the same size, profile and bolt pattern.

Thats probabbly everything that applies Douse.

incorrect, that's the old ruling, its since been replaced/updated.

read the 'National Code of Practice' for the current ruling.

i think that they should make a website or something stating how low you can go and what you can have permits for in your car or what you can put etc etc... my bad if they have this already

they do. its called the 'National Code of Practice', and covers everything to do with vehicle modifications.

google it and you shall find everything you need to know.

wow.. when did that come into affect?

it came and went. :rofl:

We even still have that in our "vehicle handbooks" (which has a section for vehicle modifications, so the 'old ruling' must still be correct in WA.

However, i don't really give two peanuts, so i'll just get over the pits on wednesday and then back to the way it was before minus the screamer lol

I just got a yellow sticker after seperating from the ddd cruise.

For : my blue parking lights at the front.

I wouldnt have been pulled if my fog lights didnt accidently come on though

So i am epicly annoyed that i have to go to the pits and make the efforttttt

/rant

I failed the pits on Wednesday for the tread on the rear tyres not being even due to camber wear (however, the rear tyres are not down to the inside markers yet, and the minimum tread depth level is 1.5mm, my rears have about 5mm left on them >.<), my blow-off valve being too noisy but its the stock BOV o.O, and my brake light in the spoiler not working ><

Oh well, at least i know they will only check these things when i go back over the pits :)

everytime ive had a sticker ive had to call the pits EG warwick and book it in.. not many places just let you rock up these days

http://www.dpi.wa.gov.au/licensing/licensingcentres/1453.asp

theres a link with there numbers :)

Rim width must not exceed the maximum rim width specified by the manufacturer by more than 25mm (1") (for passenger vehicles manufactured after 1st January 1973, the manufacturers rim width shall be taken as that specified on the tyre placard).

In any event, rim width shall not exceed 177.8 mm (7") unless specified by the manufacturer as standard equipment for the vehicle in question. No increase in rim width is permitted for vehicles fitted with original equipment rims in excess of 177.8 mm (7") width.

The tyre to rim fitment must be in accordance with the Tyre and Rim Association Manual.

All wheels must be the same size, profile and bolt pattern.

Thats probabbly everything that applies Douse.

this ruling went out about 3 years ago

ruling is now 1.25

ie:: r32 gtr stock runs 16 x 8 equates to 16x1.25 = 20 //// 8x1.25 = 10

therefore a r32 gtr can legally now run 20x10 rims

this was explained to me by Reno the head guy at welshpool pits when i got my gtr registered with 17x9's on it

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • All of those are near new/brand new/done under 10,000km! This means something! It also doesn't necessarily mean anything.... The idea is of course to fit wider tyres and rims, and to go with engine head updates, I'm sure it will be faster the subsequent time out. But TBH the difference will largely be in driver mod between one day and the next I'm sure. To say I am unseasoned after many years away from even driving remotely fast is an understatement. Giving it half throttle and "Whoa, that's a bit excessive.." and realizing I'm doing 80kmh in a 100 zone is evidence enough lol. I have noticed that there is heat haze/steam/air/something absolutely steaming out of the car after parking it. I didn't drive it in the 40C day for testing yesterday, but on Christmas day it was ~32 and you could literally see the air coming out from the bay after parking the car. Whether that's enough though..   
    • I'll take clutch for 50 Eddie.
    • Standard GTRs are boring and there plenty of them, do what ever you want to it and just remember nothing about them is cheap anymore and if you’re picky about how you want things done it gets even worse.    if it’s an n1 or something very limited then maybe care more about it’s heritage 
    • Alright guys, I've got good odds the motor survives due to a majority of spare parts. Who's taking bets on clutch, who's on transmission, and who's go diff? Happy to also take bets on if it still overheats in traffic or not 😛     Car looks amazing by the way. I've never been a fan of R34 rears, so really, I don't think any body kit etc solves that for myself, but the front end looks amazing!
    • As an ex-skyline owner Going off how these things are now "modern classics", I would keep the twins and just "refresh" bits that are required for reliable power and have a car you can take out for a cruise whenever you get the itch As a idiot who cannot leave things alone Going deep into the "rabbit hole" is a easy thing to do, as previously mentioned, once you start it becomes a slippery slope, wirh lots of supporting mods, and possibly rebuilds, and unless you have a bottomless pit of funds, the car can spend most of its life sitting in the garage,  broken, waiting for parts, or building more funds For a classic like a R32 GTR Basically, a reliable OEM+ refresh, that isn't a broken garage queen, is alot better than a car that you build, then break, then fix, then break again And it isn't just the engine you need to worry about, these beasties are getting on in age, and all parts are getting, and have got, expensive, the days of picking up cheap replacement engines and other driveline parts are well and truly over The funds not spent on going a single with quality parts, and with all the other other bits required to make it happen, could be spent on refreshing alot of other parts A wise man once said "If you cannot afford 2 GTR's, you cannot afford 1", I also believe he said this about 20 years ago when you could pick up a clean R32 GTR up for around $20k My advice for a R32 GTR (the one and only true Godzilla in my mind) is to think holistically about the whole car, the body, the power train, the suspension, the brakes, and the driveline SAU is a wealth of knowledge with decades of Skyline experience,  from stock, to OEM+, to modified to varying degrees, to full on or weekend or dedicated racecars, as well as full on money pits that rarely leave their garage Treat the old girl nice and give her what she deserves, you are a lucky man to own such a classic car  
×
×
  • Create New...