Jump to content
SAU Community

Recommended Posts

ok this is line3's brother

line3 was just out driving only a few minutes down the road on the highway, he was driving normally until he went to change gear and he lost ALL pressure in his clutch.

he's managed to get the car off the road but he cant get any pressure in the clutch at all.

he never had a problem with the clutch and has never fidled with it ever.

i know the basics of the clutch system from my z32 but not familiar with the skyline.

its a N/A r33 gts manual.

if anyone knows what i should look at or can give me any advice or even help please reply.

the cars on the side of the highway and we will not be leaving it there

Link to comment
https://www.sau.com.au/forums/topic/275467-emergency-no-pressure-in-clutch/
Share on other sites

hey guys.

i've bled the system and i'm getting some pressure back in the clutch but not much.

i've been told the slave and master cylinder may be stuffed, my brother has his 300zx wreck in the garage and he has both the master and slave cylinders both in good nick.

can i use the z32 master and slave cylinder in my r33 gts?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • These are small points I should actually add to my original post. GKtech makes an extended slave line for this conversion. It's what I use, and it works well. You'll also need a CD009 slave cylinder.  S/R Chassis Z33/Z34 Conversion braided clutch line As for transmission sensors, you'll need to both extend the wiring and replace the connectors. I can't recall which is which, but one is your neutral switch and the other the reverse switch. As they are just switches, just test for continuity with your transmission in neutral or reverse to figure out which is which. Connectors:  VQ35 neutral Switch Connector | Wiring Specialties VQ35 Reverse Switch Connector | Wiring Specialties 
    • I’ll try and see it could be the release bearing. As for the 4th gear grind maybe clutch doesn’t disengage properly cause it is slightly like very slightly hard to go into first could be due to the slab cylinder pin being short uni clutch is a twin plate.   Ive attached some assembly photos hopefully you can open the link and see maybe detect what’s wrong https://share.icloud.com/photos/0dc2YvW__Hl6jl-l2_0jejjpg https://share.icloud.com/photos/09e0jkWOK-vP48c1cfY6u3ViA https://share.icloud.com/photos/0b4rDmh5R7pK7fb1VtND73a3g https://share.icloud.com/photos/05eeUi_6dC4DVi80jOUYDgb0g https://share.icloud.com/photos/06335TgY1XxyIJal_wkdQLhzw
    • Yeah for sure that is peddle adjustment 
    • What are your thoughts on this after having it for a while, worth getting?
    • Downshifts are harder on transmissions than upshifts, the input shaft naturally slows down once disconnected from the engine so the synchros aren't doing all the work. There's no "natural" tendency for an input shaft to increase RPM. Something is not right there, I don't have a great answer on what. You can try a dedicated GL4 75W90, I plan to switch to Motorcraft XT-M5-QS which is supposedly a very good 75W90 for NB Miatas which have a weirdly sensitive transmission from the factory. I would chase down why your clutch is making a hissing noise, that's not normal. It might be no big deal but in the absence of anything else to investigate I would look at that.
×
×
  • Create New...