Jump to content
SAU Community

R33 Just Got Out From The Dyno, Awesome Result!

Nick378

By Nick378,
in Engines & Forced Induction

 Share

Recommended Posts

SS8_Gohan Grand Master

SS8_Gohan

Posted
Posted

Trent's dyno sure as doesn't read high? compared to RE's roller, i think my car at Trent's was less 2-3rwkw.

From what little i know, i think the main thing in this thread is that 19.5psi on stock internals is a bit of a ticking time bomb, regardless of the tune i thought...

18psi is pushing it, and that's NEO head which flows better, so a non-NEO RB25, 19.5psi i can't see lasting long. Never know though, see how you go :P

Guilt-Toy Grand Master

Guilt-Toy

Posted
Posted
ok guys, i'll take it to the track and post the result lol.

For now, when i change gear at 4000 and over there is a cloud of white/blue smoke lol...

Get the turbo checked.

R31Nismoid Grand Master

R31Nismoid

Posted
Posted
Trent's dyno sure as doesn't read high? compared to RE's roller, i think my car at Trent's was less 2-3rwkw.

From what little i know, i think the main thing in this thread is that 19.5psi on stock internals is a bit of a ticking time bomb, regardless of the tune i thought...

18psi is pushing it, and that's NEO head which flows better, so a non-NEO RB25, 19.5psi i can't see lasting long. Never know though, see how you go :P

we are talking hub vs chassis... two different methods

Birds Grand Master

Birds

Posted
Posted
The engine will be fine as long as you still have some meaty AFR. 20psi is fk all

There is more to engine wear than just boost pressure. Engine internals have their thresholds based on several variables including torque, heat, engine speed etc.

Jet30 Apprentice

Jet30

Posted
Posted
There is more to engine wear than just boost pressure. Engine internals have their thresholds based on several variables including torque, heat, engine speed etc.

Agreed, just basing on what I've seen the standard rb30 bottom ends handle (excess of 350rwkw standard). If he is sensible with his rev range and in good condition I'm sure it will last quite a while.

Evan_R33 Enthusiast

Evan_R33

Posted
Posted

Jesus. Who gives a rats what power it has or hasn't got?

go to the track and lets talk about that. it could have 1, 000 000 hp but who cares!? I just love how someone posts up a result then all the 'experts' around tear them a new one! I think most dyno sheets can be taken with a grain of salt. as long as the tune is healthy who really cares?

I think a simple "good for you" and if you don't believe the results keep it to yourself.

my 2 cents

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Milkmun
      The FD RX7 is the best looking 90's JDM car

      By Milkmun · Posted

      Lucky man, who owns it in the family? Any pics? 
    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      The engine stuff is Greg Autism to the Max. I contacted Tony Mamo previously from AFR who went off to make his own company to further refine AFR heads. He is a wizard in US LS world. Pretty much the best person on earth who will sell you things he's done weird wizard magic to. The cam spec is not too different. I have a 232/234 .600/603 lift, 114LSA cam currently. The new one is 227/233 .638 .634. The 1.8 ratio roller rockers will effectively push this cam into the ~.670 range. These also get Mamo'ified to be drilled out and tapped to use a 10mm bolt over an 8mm for better stability. This is what lead to the cam being specced. The plan is to run it to 6800. (6600 currently). The Johnson lifters are to maintain proper lift at heavy use which is something the LS7's supposedly fail at and lose a bit of pressure, robbing you of lift at higher RPM. Hollow stem valves for better, well everything, Valve train control. I dunno. Hollow is better. The valves are also not on a standard valve angle. Compression ratio is going from 10.6 to 11.3. The cam is smaller, but also not really... The cam was specced when I generated a chart where I counted the frames of a lap video I had and noted how much of the time in % I spent at what RPM while on track at Sandown. The current cam/heads are a bit mismatched, the standard LS1 heads are the restriction to power, which is why everyone CNC's them to get a pretty solid improvement. Most of the difference between LS1->LS2->LS3 is really just better stock heads. The current cam is falling over about 600rpm earlier than it 'should' given the rest of my current setup. CNC'ing heads closes the gap with regards to heads. Aftermarket heads eliminate the gap and go further. The MMS heads go even further than that, and the heads I have in the box could quite easily be bolted to a 7.0 427ci or 454 and not be any restriction at all. Tony Mamo previously worked with AFR, designed new heads from scratch then eventually founded his own business. There he takes the AFR items and performs further wizardry, CNC'ing them and then manually porting the result. He also ports the FAST102 composite manifold: Before and after There's also an improved racing crank scraper and windage tray. Helps to keep oil in the pan. Supposedly gains 2% power. Tony also ports Melling oil pumps, so you get more oil pressure down low at idle, and the same as what you want up top thanks to a suitable relief spring. There's also the timing chain kit with a Torrington bearing to make sure the cam doesn't have any thrust. Yes I'll post a before and after when it all eventually goes together. It'll probably make 2kw more than a setup that would be $15,000 cheaper :p
    • MBS206
      Can't put strut back

      By MBS206 · Posted

      Because the cars wheels are on blocks, you slide under the car.   Pretty much all the bolts you touched should have been put in, but not fully torque up.   Back them off a turn or two, and then tighten them up from under the car with the wheels sitting on the blocks holding car up in the air.
    • MBS206
      Can't put strut back

      By MBS206 · Posted

      Yes. Imagine you have the car on the ground, and you mine away all the ground under and around it, except for the area directly under each individual wheel. That's exactly how it'd look, except the ground will be what ever you make the bit under each wheel from
    • GTSBoy
      Can't put strut back

      By GTSBoy · Posted

      Yes, if you set the "height" right so that it's basically where it would be when sitting on the wheel. It's actually exactly how I tighten bolts that need to be done that way. However....urethane bushes do NOT need to be done that way. The bush slides on both the inner and outer. It's only rubber bushes that are bonded to the outer that need to be clamped to the crush tube in the "home" position. And my car is so full of sphericals now that I have very few that I need to do properly and I sometimes forget and have to go back and fix it afterwards!
×
×
  • Create New...