Jump to content
SAU Community

Recommended Posts

Hi guys,

I'm looking for a set of rims that can be good both for drifting and daily using on my R34GTT, because I'm quite new in this area and dont know much abt it, so hope u guys can give me some suggestion on that.

My friend told me is better 17' in front and 18' in the rear, but most sets I found are all 17' or 18' around. Also I was told front should be around 8'~8.5' wide and inthe rear should be 1' wider, so what u guys can suggest me?

Link to comment
https://www.sau.com.au/forums/topic/276318-rims-suggestion/
Share on other sites

honestly, you couldnt drop a more broad question on us. there are a million wheels out there, thousands which meet the current criteria you have set.

if you just want something to get around on and to do the job, find some structurally in tact 2nd hand rims for cheap, anything from 16-18" in diametre, 8"-10", that are made from a reputable manufacturer.

if you wanna know which tyre is better for drift, well it depends on ur budget, 17" is a good middle ground as it's cheaper, yet still fairly low profile and wont flop around a lot. the 18" will feel better as it will be more responsive, but u may sacrafice a bit of grip, and the tyres are more expensive.

without any more details its hard to reccomend u a lot as it's just one of those things ull have to develop over time, i can tell u what works well on my car with my setup, and someone can tell u what works on their R34 with a similar setup to urs, but each car is different, and each driver is different.

if it was me, id start off by looking for something around the 17x9 mark, i wouldnt wanna go below 17x8.5 for the front, and id prefer to have 17x9.5 for the rear. ideally id look for a pair of 17x9's for the front, and 17x9.5's for the rear. this size puts u in the ballpark, then id experiment from there. this allows u to start with the same width tyres all round, and work back from there going wider on the rear if you feel the need too.

remember, it's easier to get the balance right with wider rims than thinner rims with drift, if ur rims are thin, and u wanna go wider ull find urself bulging tyres and giving ur car a sloppy feel, if ur rims are wide, and u wanna go thinner tyres to help the balance, ull just start stretching, which will only improve feel.

Link to comment
https://www.sau.com.au/forums/topic/276318-rims-suggestion/#findComment-4677673
Share on other sites

Thanx for ur suggestion mate! :) They should be very helpful caz I'm just a beginner for drifting... And beginner always asks silly question... :) But, really thanx for that and sounds like I'd better start with 17", to save money~ :rofl: And then I think I will learn through these.

Cheers

honestly, you couldnt drop a more broad question on us. there are a million wheels out there, thousands which meet the current criteria you have set.

if you just want something to get around on and to do the job, find some structurally in tact 2nd hand rims for cheap, anything from 16-18" in diametre, 8"-10", that are made from a reputable manufacturer.

if you wanna know which tyre is better for drift, well it depends on ur budget, 17" is a good middle ground as it's cheaper, yet still fairly low profile and wont flop around a lot. the 18" will feel better as it will be more responsive, but u may sacrafice a bit of grip, and the tyres are more expensive.

without any more details its hard to reccomend u a lot as it's just one of those things ull have to develop over time, i can tell u what works well on my car with my setup, and someone can tell u what works on their R34 with a similar setup to urs, but each car is different, and each driver is different.

if it was me, id start off by looking for something around the 17x9 mark, i wouldnt wanna go below 17x8.5 for the front, and id prefer to have 17x9.5 for the rear. ideally id look for a pair of 17x9's for the front, and 17x9.5's for the rear. this size puts u in the ballpark, then id experiment from there. this allows u to start with the same width tyres all round, and work back from there going wider on the rear if you feel the need too.

remember, it's easier to get the balance right with wider rims than thinner rims with drift, if ur rims are thin, and u wanna go wider ull find urself bulging tyres and giving ur car a sloppy feel, if ur rims are wide, and u wanna go thinner tyres to help the balance, ull just start stretching, which will only improve feel.

Link to comment
https://www.sau.com.au/forums/topic/276318-rims-suggestion/#findComment-4677684
Share on other sites

yeh 17" is a good size, the issue with anything smaller is it's just too hard to find much over 8" wide, which for a turbo skyline, is just too thin imo. the 17" is still relatively cheap, but has a decent range of widths.

Hi mate, just send u a PM, but forget to send u the link, here it is: http://www.nissansilvia.com/classifieds/vi...g.php?view=2353

Cheers

Link to comment
https://www.sau.com.au/forums/topic/276318-rims-suggestion/#findComment-4679613
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • My idle is set at 950rpm though - Moving the timing around 20 degrees is not really what I'd call a calm idle. That said... neither is chop, by definition. The LS ECU likes to adjust timing to hold idle as opposed to air. It'd work, but generally speaking there'd be a discrepancy in the base idle and the IACV would want to move the timing around anyway to maintain said idle. I think I'm just going to keep the timing steady anyway. Preserve my engine mounts.  My aircon is now officially regassed. As the guy was reversing I noticed my reverse lights do not operate, along with my reverse cam. This is a bit distressing, because 100% of guides talk about which wire to connect to backup cams as "the goes with the [other color] wire". Often when doing conversions. Unfortunately the R34 colour wires aren't documented Unfortunately I had a T56 Magnum gearbox with it's reverse switch, which also isn't documented. Unfortunately there's definitely not documentation for people with both of these in the one car. Unfortunately I forgot. After many hours of this, I have a reverse cam and reverse lights again. The wire going through the trans tunnel to the reverse switch had broken. Upon inspection, it looks like this one wire had about 7 spade terminals and extensions in it.. for reasons I cannot possibly comprehend. I also spent the 750 hours required to clean up the wiring behind my head unit which now looks like this: This is a monumental improvement relative to what used to be there WRT triple gauges, head unit, traction control, wideband controller, and whatever the f**k OEM stuff still exists there in various states of connectivity/needed. Next step is to check in at the Exhaust shop to see/confirm how much clearance I have, to decide what mid mufflers or 'resonators' (which are just straight through, narrower mufflers) I can add and hopefully cut out a lot of exhaust leaks, pinhole, v-band or otherwise. But first step will be to 'take a look' before the next step.
    • Fark the AFM card and Nistune, Haltech Nexus S3, DBW, cruise control, flex fuel, dis dat.  
    • It's most likely the bolt/bush where the cover bolts back wore and allowed cover to move forward.
    • Still haven't put the injectors and R35 AFM in so we can tune the bloody thing for the HG highflow it got mid last year! I think I can forecast the upgrade path to a bigger twin scroll, external gate, Haltech, flex setup, Samsonas, dis dat, etc will be .... a while away!
    • Should have taken that opportunity to slot in a twin scroll turbo setup. Maybe next time.
×
×
  • Create New...