Jump to content
SAU Community

Recommended Posts

Hi Guys,

Buying an Apexi AVCR very soon.

Just want to know if i can hook up an external switch (i.e. not by pressing a switch on the avcr face) to change between hi and low boost?

My idea is to have a switch on my dash which allows me to run low boost, then when i punch this switch the AVCR switches to high boost setting.

Does anyone know if this is possible?

Cheers

Link to comment
https://www.sau.com.au/forums/topic/276576-apexi-avcr/
Share on other sites

Excuse the incorrect use of language, but you dont want to use a missile switch. The AVC-R has two boost settings so yo ujust go to the setting you want to run. A missile switch is a two pole( Language???) switch . You want a sinle contact button so that only whilst pressed it will complete the circuit thus giving you the scramble

I have a button on my old steering wheel for it. Though i never really had enough power to justify using it. I actually used it to drop boost with the scramble feature. So when launching in 1st gear i only had 8psi then in the higher gears i used to use the normall Setting B high boost setting of 15psi on my std turbo. Like i said never really had enough power to justify using it that way, maybe make use of it now that i have more power but i dont run it anymore :(

Link to comment
https://www.sau.com.au/forums/topic/276576-apexi-avcr/#findComment-4682595
Share on other sites

whats the point? why not just tune the car for the maximum possible safe boost you can run

and use the avcr tuning ability to curve the duty to correct wheelspin etc

most people break things when their car is setup for a safe level

and they have a switch to go higher "for short runs"

if you run higher, why not run higher all the time

Link to comment
https://www.sau.com.au/forums/topic/276576-apexi-avcr/#findComment-4682608
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • GTSBoy on your suggestion on another thread I had a look at those injectors and ended up getting them because of the quality.  Got the expensive ones.  
    • Hey guys been looking everywhere to try and find the correct gtr hood latch support part number but only found the first half and when I search with that number it sends me to an r34. The first part I found was 62515. If anyone could help me with the rest then I’d really appreciate it. Or if there’s some alternative hood latch support that would work even better cause I can’t find any for sale. (Searched on upgarage, partsouq,buyee,rhdjapan) 
    • If you've only done the upper control arms on the rear, AND you have changed their length (by more than about 1mm) to set the camber you want, then you will definitely need/want to install traction arms also. Adjusting the camber arms on their own WILL introduce bump steer and make the car unpleasant to drive. Most owners have no idea that their car could behave infinitely better than what they put up with. I'm not entirely sure what the Stageas need, but I am thinking that unless you have massive front spring rates and pretty soft rear springs, you have waaaay too much rear bar. Oversteer city, in my estimation. Combined with possible excessive bump steer from maladjusted arms, that could be a recipe for nastiness. ATR43SS2 is not a highflow. It is an outright replacement turbo. It's a little bit bigger than the largest highflow profile that Tao does. Probably a solid 300rwkW turbo where the bigger highflows will be about 30-40rwkW less. Nevertheless, we're only talking about ~300 rwkW, which is well within the abilities of the stock ECu to run with a Nistune on board. I would do so without hesitation - and I will be doing so when I get my finger out and actually get the injectors and AFM installed. But, if you would prefer to drop a whole lot more money on the ECU side, then I suspect you're looking at Haltech. The Haltech fanbois here will all spout on about all the available engine protection you can have, that you can't have with the Nistune option. And they're right. But it doesn't really come for free either. You will spend more money on extra sensors and the like, plus the work to install them. If the engine was built and therefore represented a big investment to protect, then I'd say definitely do it. If you view the current (and forever into the future) shortage of replacement engines as something to prompt similar protection, then also, do it. If you see a destroyed RB25 as an opportunity to put in a Mercedes or other V12 (like I kinda do)... then your perception of the risk/reward might differ. These are good injectors. You can also get a "better" set of the same with more flow matching, for more $$. 1000cc is where you will want to be. You will need an R35 AFM and adapter tube if you want to stay with Nistuned stock ECU. Otherwise, if going Haltech, you can ignore. As for intercooler. Just about anything will do. You're only talking about ~300rwkW. Just put a big core in there. Be aware that return flows do add significant pressure drop and will cost power and will make the turbo work harder to achieve the same goals. If you can manage a proper crossflow, do it. I'm keeping my very good return flow because I'm only expecting to be in the ~250rwkW range, and will live with whatever outcome I get.
    • I have a heap that i have collected if you want some authentic ones still. Pm me if your interested!
×
×
  • Create New...