Jump to content
SAU Community

Recommended Posts

Hi i have a strange hicas problem.

Car is 1993 R33 Sedan Auto RB25DET

The HICAS usually light on every second start of the day.

Which means everyday when I first start my car, it is fine.

Till I reach somewhere and turn off the ignition, after a while turn on again, the HICAS light will comes on.

So it is like, for a non-cold start, the hicas will light on.

Everything is fine, all fuses are checked (under driver's side and rear boot).

Mechanic asked me to seek help from a power steering specialist.

What do you guys think?

I tried to run the HICAS diagnostic but it never success, tried a couple times and the engine check light never flash.

I wonder is there anyway to diagnosis the HICAS?

has anyone encounter this before?

also does HICAS affect fuel consumption? cause I have been having 16L/100kms for a very stock car.

should I remove the HICAS with a lock bar for daily driving (normal drive)?

car had just recently been major serviced.

Link to comment
https://www.sau.com.au/forums/topic/276622-hicas-problem/
Share on other sites

Hicas Problem:

HICAS Solenoid R.H.

HICAS Solenoid L.H.

Fail-Safe Valve

Vehicle SPeed Sensor

Steering Angle Sensor

Steering Neutral Position Sensor

Parking Brake Sensor

Inhibitor Sensor

among these i think only fail-safe valve and inhibitor sensor is related to car temperature?

when the coolant temperature is low and if the car is ignited there will be no HICAS

it's just when it is non-cold start then HICAS will turn on

what is fail-safe valve (where is it?)

and inhibitor sensor

could someone explain?

cheers

Link to comment
https://www.sau.com.au/forums/topic/276622-hicas-problem/#findComment-4682915
Share on other sites

easy solution is to just get a hicas lock bar and remove the worry all together. Remove the hicas light out of the dash and regularly check your power steering fluid to make sure its topped up.

I read somewhere a very long time ago, and I dont know if this applies to the newer models of HICAS where they dont use the powersteering fluid to work, but apparently if there is an Air bubble in the lines (or if it wasnt bled properly) that could possibly trigger the warning light. In saying that, try bleeding the powersteering fluid properly and see how you go.

Link to comment
https://www.sau.com.au/forums/topic/276622-hicas-problem/#findComment-4685554
Share on other sites

easy solution is to just get a hicas lock bar and remove the worry all together. Remove the hicas light out of the dash and regularly check your power steering fluid to make sure its topped up.

I read somewhere a very long time ago, and I dont know if this applies to the newer models of HICAS where they dont use the powersteering fluid to work, but apparently if there is an Air bubble in the lines (or if it wasnt bled properly) that could possibly trigger the warning light. In saying that, try bleeding the powersteering fluid properly and see how you go.

yea I am thinking to remove the HICAS with the lock bar but people around me suggest me to find out the problem before removing it because it indicates a problem

my power steering fluid has been changed lately after a major service tho

Link to comment
https://www.sau.com.au/forums/topic/276622-hicas-problem/#findComment-4685559
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Waaay ahead of ya....(evil laugh!!) Will show the fitment and spec details later when it isnt as rainy !
    • Thanks Dose.....    I appreciate it!!
    • I'll probably be putting the shit box back on the dyno again soon, I want to dial in the closed loop boost control properly. I'll have a camera facing the car/motor for fun too. Just note, there are essentially 3x 10AN inlets going into the catch can and 1x going back to the intake pipe. Most of the time the catch can "return" to the sump actually is the crank case breather, pushing air out.
    • I have the R3C with a Nismo slave and by no means does it behave like a stocker, it ain’t THAT bad. On take off just give a bit more throttle than you would say a coppermix and it’s fine. It will not slip though.   
    • Okay. Final round of testing done. Got a friend to hook up a fancy scanner to the car and we also ran some compression and leakdown tests, she is healthy.  The MAF was definitely the culprit. So for future reference anyone with similar issues that find this thread. I suggest the following steps, in order of affordability:   Check your spark plugs for any fouling, replace plugs if they are bad or re adjust the gaps making it narrower (0.8mm would be good). Check every coil's resistance with a multimeter. It can be done by probing the IB and G pins on the coil pack. Resistance should be around 1.4 (+/- 0.1) Ohms Check the MAF. If you have Nissan connect or a good scanner with the 14 adapter it should allow you to see the voltage on the MAF reading should be around 1.1 - 1.2V when car is idling. But if you don't, buy a new MAF from Amazon and test, then return it. (For instance, I got a Chinese one for $40 that was reporting 1.3v on idle). If you still have scanner, you can run tests on the injectors to see if they are working, just remember to unplug the fuel pump fuse/relay and have no pressure on the line. Then listen for the noises that the injectors make. Clean/replace injectors as needed. Once you find the issue and fix, order thousands of dollars worth of OEM parts to refresh unrelated things (Optional)   PS: Thanks to the absolute legends of this forum for the responses and help to someone that went a bit over their head. (me)
×
×
  • Create New...