Jump to content
SAU Community

Recommended Posts

I've got a track day on Sat at Sandown and the forecast looks to be wet. I have RE01Rs for the road and RE55 (SR2s? - can't see the car now to confirm but not wet weather ones, just normal) for the track so not sure what's best for the day. I've run the RE55s and some Dunlop D01Js in the wet (road) and was always pleasantly suprised by the grip on offer.

Any thoughts on the best way to go? My guess would be that other than large amounts of standing water, the RE55s would be a better bet.

Commnets and suggestions please.

Cheers.

Link to comment
https://www.sau.com.au/forums/topic/276932-tyre-selection-for-a-wet-track/
Share on other sites

Thanks guys. I'll take a look at the forecast the day before and perhaps speak to someone who knows the track and see what their view is. Wish me luck as iIm nervous being on the track in the wet! I guess I'll have to slow down, feed the speed in, and not take any risks on the faster corners.

As it happens I did a track day in the wet last weekend. On RE55's. They were new though.

To be honest they are fine - even to the point where there are puddles on the track. Just try & drive around the said puddles as you can get aqua planing at spots you don't want to.

Corner grip is pretty low & your biggest issue will be having a lose under brakes. Just keep it straight & everything will be fine.

You can be confident that your times will be ok as most people who take road tyres wont be going hard & anyone on R compounds will be in the same boat as you.

I've done a hillclimb at Mt Cotton in heavy rain on RE55S. There were sheets of water running down the hills towards you. The RE55S were great in the wet there, but it is low speed compared to Sandown.

IMO semis are always faster in the wet than street tyres. I've certainly never been beaten by anyone running street rubber in the wet. And you don't see Improved Production guys swapping to road tyres in the rain - you can bet your arse if it was faster they would! Street tyres evacuate more water, but the hard compounds are not going to give you any grip on a cold wet surface.

slightly higher cold pressures in the wet - you won't generate as much heat in the tyre and won't get to your normal target hot inflation pressures. Try 2-4psi higher cold.

Thanks. Can you tell me off what base? e.g. normally set to 28psi cold for dry conditions. Run 28+4 for wet. etc etc.

the way I do it (it may not the best way but it works for me) is to aim for the same hot pressures as you normally end up with in the dry. On multi lap sprints that seems to generally be about 4psi higher than my normal cold starting pressure. So yes, if you normally start with 28psi cold, try 32 psi cold and see if you hit your normal hot pressure (probably around 36 I'm guessing?) after the first session, then adjust from there.

OK, lay it on me brothers. I need to be told directly what psi to set my tyres at tomorrow. __psi for a wet track. I'd just whack 30 in em without any further guidance so if that aint the figure, can you give me one? It'll be wet and cold at the track tomorrow so I'll not be stuffing around with pressures whilst I'm there - yes, I'm weak as piss. I'm also fiddling with the suspension so will only have time for that.

Cheers.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Not that I know from experience, but in theory you'd want your gate spring to be as close to target pressure as possible, so you'd go with the higher gate spring?
    • Before I commit to it as I already have the wastegate off the car, would you change it to the 9psi spring instead of the 12, or whack it back on now and try your suggestion?   Edit: Actually I might just swap the spring and see what the logs say after another few pulls, as we know it's still spiking without the Mac valve in the picture so I need more data without the Mac valve trying to combat the issue.
    • Sounds good Hmm suppose the main thing is, how much do you care about this car? The filler doesn't make for a very good water barrier lol. If there was a tiny little bit of rust forming now, that in 3 to 5 years time becomes obvious under the paint (starts to bubble up), would it bother you? 
    • I already have the ability to datalog the voltage... what I can't do is correlate it to what the gauge is showing when I'm looking at the data at a later date. Or something like this. Except getting the oil to 125C+ involves me going 200+kmh at the track so you can imagine this is a little tricky unless I do something like note what the voltage is when I am at the top of 5th gear so I have a point to reference on. Drove car today. O2 still reading richer because hopefully not a leak instead of massive restriction I've introduced. Car really doesn't sound like a LS. It's quite strange. Pulled a bit of fuel out up top. This does potentially explain why my spark plugs looked like the car was running pretty over-rich. If I was tuning it to a ~12.7 which in reality was far richer than that in the past. It will be handy to have the dyno WB to compare my WB to to compare notes that's for sure. At this point I'm happy to just sit in the passenger seat and tune the thing given I've got about 7 million hours on the platform lol.
    • Yeah I understand you have to pay for an updated map or subscription service or something. But I can't even find a current map for Australia. My map is dated 2017, but didn't this car version still sell in Australia until 2021?   Also, just as an aside, the navigation system warns you of traffic incidences ahead.....why would they include that on a map they knew is not receiving live information. I am forever going to be warned of an incident that probably existed for 30 minutes 8 years ago.
×
×
  • Create New...