Jump to content
SAU Community

Recommended Posts

Hey guys,

I've just purchased a complete R34 that i'm parting.

- Pair R34 Xenon's + loom for a R34 light conversion (inc. plugs / ballast / bulbs) $1500 AU

I'm located in Auckland, NZ so i'm only able to ship smaller parts. Anything to large to send won't be for sale here.

But PM me or reply here on any parts you want.

- Tiptronic

- RB25de

- 110000 km's

- Pearl White

71198351.th.jpg

72265125.th.jpg

Cheers :laugh:

Edited by Chang
Link to comment
https://www.sau.com.au/forums/topic/277068-wrecking-complete-r34-sedan/
Share on other sites

Hey guys,

I've just purchased a complete R34 that i'm parting.

- Pair R34 Xenon's + loom for a R34 light conversion (inc. plugs / ballast / bulbs) $1500 AU

I'm located in Auckland, NZ so i'm only able to ship smaller parts. Anything to large to send won't be for sale here.

But PM me or reply here on any parts you want.

- Tiptronic

- RB25de

- 110000 km's

- Pearl White

71198351.th.jpg

72265125.th.jpg

Cheers :laugh:

INTERESTED IN XENON LIGHTS...STILL AVAILABLE?

Sorry Rance, Bonnet is too large to send via NZ to AUS.

lanky71, Xenon headlights are gone. But I still have a set of Non-Xenon's available.

666dan, yes it does have the cup holders. But going with the centre console.

But I have Pm'd the rest of you guys.

Edited by Chang

Here's a rough price list

Exterior:

Left / Right Non-Xenon headlights $1000

Left / Right wing mirrors $200

Monsoon / whether shields / wind deflectors $100

Rear wiper + motor + loom $100

Tail lights (tinted lenses) $160

Interior:

Airbag system (complete) Tiptronic steering wheel / Passenger airbag / Airbag computer $500

Air con unit (damaged face plate but still working fine) $60

A pillar trim + boost gauge (not branded) $80

B pillar trim (lower centre trim) $80

C pillar trim (rear where rear seat belt comes through) $80

Centre dash vent $80

Centre console (with leather lid / compartment) $120

Complete set (5x) seat belts inc. bolts and buckles $200

Door sill trims $80

Speedo cluster surround $60

Tiptronic shifter $100

Tiptronic shifter surround + ash tray $80

Tiptronic cluster, approx 110,000 km’s $150

Misc:

RB25de Neo ECU computer $100

Edited by Chang
Sorry Rance, Bonnet is too large to send via NZ to AUS.

lanky71, Xenon headlights are gone. But I still have a set of Non-Xenon's available.

666dan, yes it does have the cup holders. But going with the centre console.

But I have Pm'd the rest of you guys.

What if I supply you with the factory 'blank plate' that normally sits in that location? Then the centre console is still complete for you to sell.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I know this one’s the BB one. My tuner did make mention about the actuator. I am curious about the VCT as well
    • Might also needs a stronger actuator with the right preloading. With older 2019 built bush G3 units, BB upgrade or 21U housing down size makes a pretty decent gain in response as well. 
    • Hey lads  so im finally putting together my rb30 forged bottom end and ran into an issue. I measured my main bearing clearance with arp main studs torqued to 60 ft-lbs using ACL H series STD size bearings and standard, un-ground crank shaft journals and got an oil clearance reading of about 1.3 thou measuring straight up and down and about 2.8 thou measuring at a 45 degree angle (just above and below the parting line). My machine shop said they measured the main tunnel and it was all within spec (they didnt say the actual measurement) and to go with a standard size bearing, which i have done and the clearance is too tight, I'm guessing because of the extra clamping force from the arp studs distorting the main tunnel. I was wanting to run about 2.5 thou main bearing clearance.  My questions are: 1. could i just use the HX extra 1 thou clearance ACL bearings? that would fix my straight up and down clearance making it about 2.3 thou, but then would the side to side clearance be too big at around 3.8 thou? 2. what actually is the recommended main bearing clearance for measuring near the parting line / side to side. i know its supposed to be bigger as the bearing has some eccentricity built into it but how much more clearance should there be compared to the straight up and down measurement? at the moment there is about 1.5thou difference, is that acceptable or should it be less? 3. If i took the engine block + girdle back to the machine shop and got them to line bore the main tunnel (like i told them to do the first time, but they said it didnt need it) what bearing size would i buy? the STD size bearing shells already slide in fairly easily with no real resistance, some even falling out if i tip the girdle up-side-down. If im taking material out of the main tunnel would i need a bearing with extra material on the back side to make up for it? this is probably confusing af to read so if something doesn't make sense let me know and ill try explaining in a different way. My machine shop doesn't come back from christmas break until mid January, hence why i'm asking these questions here. TIA for any help or info 
    • I bought the model back in Japan in Feb. I realised I could never build it, looked around for people who could build it, turns out there's some very skilled people out there that will make copies of 1:1 cars or near enough. I'm not really a photo guy... but people were dragging me in a group chat for the choice of bumper as someone else saw the car before it was finished as they are also a customer of that shop. I took the photo in the above post because I was pretty confident that the lip would work wonders for it. Here's some more in-progress and almost-done pics. It gives a good enough idea as to what the rear looks like!   I have also booked in a track day at the end of January. Lets all hope that is nothing but pure fun and games. If it's not pure fun and games, well, I've already got half an engine spare in the cupboard 
    • Well, do ya, punk? Seriously though, let's fu<king go! The colour and kit looks amazing on the car. Do you have any shots from the rear? I don't quite follow how the model came around. You bought the white kit and he modified it to match your car? Looks nuts either way!
×
×
  • Create New...