Jump to content
SAU Community

1x Used Apexi Replacement Pod Filter - To Suit Gtr Kit

KR4-GTR
 Share

Recommended Posts

KR4-GTR Mentor

KR4-GTR

Posted
Posted

Hi guys and girls,

I have 1x used Apexi replacement pod filter to suit the GTR kit.

I had this on my car and it worked ok, its other brother had holes in it so when I replaced it I just replaced them both - hence I have this one as a spare.

Its in used condition as per the picture but if bent fins dont bother you or you dont care how good it looks, you're sweet! I've tried to make it look as bad as possible in the pictures so you can see the worst case scenario.

It could use a clean. I promise im not that lazy, I just didnt clean it because there are conflicting views about whether to use oil or not - so i'll leave this up to its new owner.

I paid $130 each for the new ones I bought, but i'm willing to sell this one for the best offer. Hows $50 sound for a starting point?

I'm happy with whatever price as long as someone can make the most out of it, so just make an offer. I guess it would get you out of trouble if you have a busted one?

Pickup available from the hills district or I can post at buyers expense.

You can contact me on 0434 929 257.

Cheers!

post-54322-1246413233_thumb.jpgpost-54322-1246413326_thumb.jpg

post-54322-1246413376_thumb.jpg

KR4-GTR Mentor

KR4-GTR

Posted
  • Author
Posted (edited)

Hey mate,

PM sent - lets work something out hey!?

For starters, hows $45 sound for the filter, including registered post + insurance?

It will also be professionaly packed to ensure it will not be damaged in the post.

Your thoughts?

Cheers!

Edited by KR4-GTR
KR4-GTR Mentor

KR4-GTR

Posted
  • Author
Posted (edited)

No reply, so offer stands for everyone.

Actually, make it $40 including registered post + insurance and its yours!

Even less for pick up of course.

Cheers.

Edited by KR4-GTR
  • 2 weeks later...
KR4-GTR Mentor

KR4-GTR

Posted
  • Author
Posted

if you pick up - you can have it in exchange for friendship and a positive trader rating.

and any cash if you think its worth it - you tell me what you want to pay, if anything.

cheers!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Ozdavroz
      RB20 in need of modest love injection

      By Ozdavroz · Posted

      Do the R32s run high or low impedance injectors?
    • Duncan
      R32 GTST - 600KW+ RB28/CD009 Build

      By Duncan · Posted

      It may not feel like it to your wallet....but sounds like this was one of those "lucky you did it" rebuilds. Hopefully you have better luck this time
    • GTSBoy
      r34 gtt tall spoiler

      By GTSBoy · Posted

      It's aftermarket. It also reeks of Honda Civic tryhard from 2003. But if you want one....then you want one.
    • TurboTapin
      R32 GTST - 600KW+ RB28/CD009 Build

      By TurboTapin · Posted

      Well some mostly good news and some slight bad news.  Good news is cylinder 6 did in fact only require a honing and I'm good to run my 86.5mm pistons again. I should also get the block back by end of week. Bad news, had a few surprises pop up. First, main and rod bearings were trashed. No sign of any heat damage. I knew right away what caused this... I had not packed my oil pump originally and spent a lot more time than I would have liked cranking the motor to get oil pressure. It sounded fine once started so I chucked it up to luck and forgot about it. Luckily rod and crank are fine and just need new bearings. Engine builder agreed that this was the cause.    Another surprise that carbon covered up very well that I didn't catch, something got sucked up and went through cylinder 1, 2 and 3. Luckily this was no cause for concern, just needed a bit of cleaning up. Valves look fine but he will vacuum test the head this week to confirm. I'm presuming this was something left over from welding my intercooler piping, but we'll never know. I'm going to thoroughly reclean everything.    So all in all, happy the motor is fine, and I'll get it back much sooner than expected. I'll also be taking the time to convert my WMI system over to direct port. I'll snap some pictures of that when the parts come in. 
    • sunsetR33
      R33 GTR lift points for hoist

      By sunsetR33 · Posted

      I understand, thanks. Yeah I wouldn't want the car to tip over, I'll try and use the sills, I don't want to risk smashing the chassis rails. I ordered some rubber pucks that have a hopefully big enough slotting. If the front right gives me trouble I can always just make a wood block. I'll measure and inspect the sills closer once I actually take the car up. I hope so, but the rubber blocks I had in hand so far were pretty damn firm, if they are that hard they won't give much way. I'll let you know what happens. Angle grinding rubber isn't one of my favorite tasks. I'll probably start a build thread soon, for my own documentation and "log" as well as sharing what's going on with the car.
×
×
  • Create New...