Jump to content
SAU Community

What Is This Unit?

mwracing
 Share

Recommended Posts

Jack88 Experienced

Jack88

Posted
Posted

32's and 34's have then in the windscreen,33's do not, cant tell from the pic but if its the rear end of a 33 then that is indeed where the power antena normally goes however that is not the normaly power antenna unit so god noes what it is.

SteveL Mentor

SteveL

Posted
Posted
:huh: we skylinez dont got antenna's. its built into the front window

Actually skins is correct. Nissan's with the diversity aerial system have one aerial embedded in the front windscreen, but also use the rear window defogger grid as the second aerial. That box is a filter, which separates the power supply to the rear defogger from the aerial signal.

mwracing Collaborator

mwracing

Posted
  • Author
Posted
Actually skins is correct. Nissan's with the diversity aerial system have one aerial embedded in the front windscreen, but also use the rear window defogger grid as the second aerial. That box is a filter, which separates the power supply to the rear defogger from the aerial signal.

so its settled then? Rear defogger/antenna controller?

Just curious why my ABS/AWD/Ebrake light is on, and the two wires leading inside the trunk from that unit got cut.

I bled my brakes, and will now check the reservoir in the trunk.

mwracing Collaborator

mwracing

Posted
  • Author
Posted

that was my old mwr34 project, i dug up some old pics to show the unit easier.

I will re-connect the two wires.

One last thing, I think i noticed this even before the conversion, every minute or so while the car is running, it think i hear a relay TICK and my exterior lights pulse off for 1/10th of a second. barely barely noticable, but I am an observant guy and now it bugs me.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • MBS206
      Powder coating wheels

      By MBS206 · Posted

      I'm interested if anyone agrees with what you've said, and can give a good reason. Temperature of powder coating should be below any temperature you'd use to alter the wheel structure.  Powder coat typically 200 to 250. Annealing if that's what people are claiming would be occuring, starts at 300, and depending on the alloy, can need even up at 400+.   That's the only part I can think of that could cause an issue that people are believing it's from the rim losing hardness and becoming too soft.
    • MBS206
      One Headlight isn't working - Driver Side Fuse Keeps blowing

      By MBS206 · Posted

      Negative probe should be on the cars chassis. Positive on the wire.   Start as said above by unplugging everything (unplug the lights, and switches. Now at the switch, there is a wire from the fuse, to the switch, so out your positive on that terminal. It should read open circuit. If it reads something, especially a stupid low value, the short is somewhere between the fuse and the switch. If that's fine, now put the positive probe on the wire that goes to the headlight (at the switch plug). If it reads stupid low, the fault is from the switch, to the headlight.   Another quick test, is take the whole LED light setup from the left, and plug it into the right side, does it still blow the fuse? If you put the right hand side led light setup on the left hand side wiring, does the left hand side wiring now blow?  If the blowing fuse swaps from right to left doing this, your LED lights are the issue.
    • dyl33
      Powder coating wheels

      By dyl33 · Posted

      Anyone know if it's a problem to powder coat forged alloy wheel centers (Rays/Volk GT-C). some say it's bad and can damage the alloy, some say it's not a problem.
    • kevboost7
      One Headlight isn't working - Driver Side Fuse Keeps blowing

      By kevboost7 · Posted

      Hey guys, I'm reviving an old post but I'm finally getting around to working on this now. I removed the battery to get a better look at the wires and i traced the wires from the headlight to the fuse box in the engine bay, but the wiring looks fine? The wiring for the R/H headlight is 3 wires and then is bundled up with the large diameter wire that goes underneath the fuse box. I didn't take it apart yet. I know you said that its a short circuit somewhere between the fuse box and the headlight. But could it be the headlight switch on the dash? Also, i pulled out my multi-meter and set it on the Ohms, but i'm not sure where to put the negative probe and the positive probe.     
    • wrxhoon
      WTB R33 GTST Catch Can 2L or Bigger

      By wrxhoon · Posted

      I have a 2 lt in Sydney. It was fitted on a R33 GTR, not used for several years . If you are interested email me on: [email protected] I'm not on this forum much .
×
×
  • Create New...