Jump to content
SAU Community

Rb26 Trust Greddy Hi Volume Oil Pump And Trust Timing Belt Cover

AtomicBomberMan
 Share

Recommended Posts

AtomicBomberMan Experienced

AtomicBomberMan

Posted
Posted (edited)

Hi all, i have had a change in heart and wish to sell these items. Both are brand new in box and cost me A LOT more than what i a selling it for.

Trust Oil Pump Brand new in box includes a new genuine nissan oil seal and genuine nissan gasket. $1550 delivered

Copied these details,

It is commonly known that the stock oil pump on the RB26 engines will starve tuned engines of oil at high RPM's. When running an engine with so much time and money spent, why risk the inevitable with a stock pump? With the Greddy High Flow Oil Pump, the flow capacity will increase by 23-30% at any RPM range when compared to the stock pump. Trust guarantees high strength due to the SCM435 chrome molybdenum steel material used for the gearing. To get the most from your set-up, Trust recommends the use of their high capacity oil pan in conjunction with the High Flow Oil Pump. This pump is good for 12000rpm

l/min at 800 RPM : 5.5 (4.4 stock)

l/min at 2000 RPM : 19.7 (15.2 stock)

l/min at 6000 RPM : 59.0 (46.7 stock)

600x450-2008041200015.jpg

600x450-2008041200017.jpg

Trust Clear Timing Belt Cover $115 delivered.

Dont have pics sorry. but brand new in box.

parts are in brisbane.

Edited by AtomicBomberMan
Blitz Grand Master

Blitz

Posted
Posted
its pretty dirty if its new, why is there black on the pump if its new?

Im sure Chris will clarify, but I would think its just the angle of the photo, and probably the excess oil film that covers the pump when it comes sealed from Greddy reflecting off the black backing plate, thus making it look dirty.

AtomicBomberMan Experienced

AtomicBomberMan

Posted
  • Author
Posted

yes thats right. thanks nick. the back plate on the pump is black, and not black from oil. the oil on the back plate and over the pump is from factory. its to stop the gears inside rusting. it is not engine oil. Pump is brand new and never fitted. it still has the plastic covering the oil holes.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • dbm7
      R33 GTS25 NA - Stalling when vehicle is at operating temp

      By dbm7 · Posted

      Duh... to answer my own silly question, it's actually described in the FSM... ...400 pages away at the end of the manual, for RB25DE/DET signal descriptions, it cites the TPSwitch signal action, is dependent on the TPSensor value ~ this tends to infer the builtin POT voltage signal is the primary, and the switches are fallback/secondary should the POT fail/TPSensor signal lost (and switch alone with no TPSensor signal allows for base idle speed setting).... makes sense... they (TPS units) used to fail/wear the POT with time, they're not exactly built to last ~ having the switch as a redundancy gets around this...(or, it's less likely both signals would be lost as they're on different power rails)... and of course wrt RB26DETT, you have to electrically disconnect the IACV solenoid from the harness, to defeat idle air control...  
    • Kinkstaah
      NC MX5

      By Kinkstaah · Posted

      Dose is unaware just how much fun 145-150kw would be in a 2.5L NC MX5. It would be one of the most fun things to drive to ever grace SAU.
    • dbm7
      R33 GTS25 NA - Stalling when vehicle is at operating temp

      By dbm7 · Posted

      Same thought crossed my mind ~ depends on how one connotes 'stalling'...ie; gets a rough/stumbling idle as it get warm until it stalls... or... idles ok and simply falls-over when it gets to temp... ...you can test the whole circuit with a couple of resistors ...unplug coolant temp sensor, bridge terminals with a 2K7 resistor (ECU will do cold start), or with engine warm bridge with a 330R resistor (ECU will consider engine to be at normal operating temp)...it's a quick way to check wiring integrity/ECU response when you don't have a multimeter handy ...
    • Murray_Calavera
      Exhaust silencers/varex exhausts

      By Murray_Calavera · Posted

      They also make them with the motor mounted on the side 
    • GTSBoy
      Blue/grey smoke after idle

      By GTSBoy · Posted

      Just be warned that that turbo will not be a direct re-fit to the car. The exhaust housing is, of course, in the same place. It has to be - it's bolted to the exhaust manifold. So the dump will fit up. But the centre housing is not as long, so the comp housing will move backwards. This will affect both the turbo inlet and the outlet. There is fab work that needs to be done. Yes. it has one, it should have one. Paper gasket.
×
×
  • Create New...