Jump to content
SAU Community

Recommended Posts

Does anyone know how to get the antenna out of an R33 Series 1?

since imported from Japan the aerial never did work on mine and upon closer inspection I have found a plug floating around the aerial motor that is not connected. It has 3 wires, power, ground and the turn on wire.

All I really need is for someone to tell me where this plug plugs into on the aerial motor. Does anyone know this and if not how do I get the aerial out...?

...James

Link to comment
https://www.sau.com.au/forums/topic/27879-antenna-removalhelp/
Share on other sites

  • 6 months later...
  advance said:
Does anyone know how to get the antenna out of an R33 Series 1?

since imported from Japan the aerial never did work on mine and upon closer inspection I have found a plug floating around the aerial motor that is not connected. It has 3 wires, power, ground and the turn on wire.

All I really need is for someone to tell me where this plug plugs into on the aerial motor. Does anyone know this and if not how do I get the aerial out...?

...James

on the outside part use a sharp object to unscrew crome piece on aerial.on the inside there is two nuts that hold the jack bracket in place, plus one on the floor. remove those and the bracket. next remove the two studs left at the same time holding the aerial motor and it will come out. remove coax from aerial and there you have it.

advance, i just checked this for ya! the cable plugs into the unit on the forward (hard to get to side) of the motor ie closet to the wheel strut..... it's about 2-3 inches down from where the signal cable comes out of the arial stem!! will only plug in one way.. flat side closest to the where the arial stem is

hope this help, lemme know if you need a pic as i dont use my arial so its easy to access!!!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Most of the industry in North America either runs on Siemens or Allen Bradley. I have two redundant S7-1500's on my desk right next to me for simulation. Siemens has been losing ground though since Stuxnet, as cybersecurity is a big thing. In my line of work that is federally regulated, you must by law have a cybersecurity management program in place and its audited and inspected every so often.  I work with Emerson PLC's daily (RX3i's) and have done large biogas/refinery projects with their DCS's. Their PLC's are somewhat OK minus the way they do PLC redundancy (You have to download on both PLC's separately every time you make a change )  As for their DCS's... you'll be limited financially first before anything else stops you. Costs are exorbiant at roughly 10x what it would cost you to do with any other system (e.g AB PAC).  1990's, those suckers are brand new haha! Kraft-Heinz (An old client when I use to work for an ESP) still runs Siemens TI505 PLC's from the mid 80's. Ohh how I don't miss working with those... you could only do a certain number of online downloads until it's "Change" buffer would be full and you would then need to go offline to do a full download. There was no warning of when this was coming up and it generally would happen when you would go in at 2am to make changes before production -_-.     
    • Unfortunately, not only is that not the case, one of the main "Selling points" of safety over comms is they clearly state in writing that there's no need to segregate safety networks from non-safety networks. It always gets intermingled with everything else on an ICS/OT network. 
    • Hello. I have an a31 cefiro but since I am in Turkey we have a CA20S engine. I did some research. Then I found that I can swap with a ca18 but when I heard that it has the similar substructure as the s13. I thought I can swap with an sr20 because the sr20 was used with the s13. So can I easily swap the sr20 on my cefiro or is it difficult? 
    • I used to love stock take. I used to take f**k of a lot of stock. /Rodney Rude.
×
×
  • Create New...