Jump to content
SAU Community

Recommended Posts

Hey im assuming this is fairly normal granted its been pretty cold?? Drips a bit of water too. It all stops once its warm?

Just dont remember my old clubsport doing it quite as much...

If it stops when warm its nothing to worry about! Mine does the same when cold.:D

Link to comment
https://www.sau.com.au/forums/topic/278906-r33-gts25t/#findComment-4711510
Share on other sites

+1 to the mentioned above.....my car blows a heap of smoke when cold start and as soon as it warms up a bit then its all sweet......just try not to drive it when its really cold lol

nothing to worry about mate

Link to comment
https://www.sau.com.au/forums/topic/278906-r33-gts25t/#findComment-4711527
Share on other sites

don't warm up your car in the morning. bad for your engine. wears your plugs, allows unburnt fuel to condense and drip down past your rings into your oil diluting it.

more relative to what you're talking about, if you warm it up for like three to ten minutes it will take MUCH longer to get rid of the water vapour. Doesn't hurt your engine... it's what it's designed to do. Warming up for 5 minutes is an old wives tale. or husbands. either way, it's lame and misguided.

best way to warm up your car in the morning and get rid of the water vapour is to nanna it until it reaches just under operating temperature (a safe temp is about 70-75°, suitable op temp being between 80° and 95°C).

Try it out, the lot of you. If there's one thing you can trust, it's a dude on the internet. (That dude is Doctor Karl, bitches.)

Edited by Dorigecko
Link to comment
https://www.sau.com.au/forums/topic/278906-r33-gts25t/#findComment-4712933
Share on other sites

don't warm up your car in the morning. bad for your engine. wears your plugs, allows unburnt fuel to condense and drip down past your rings into your oil diluting it.

more relative to what you're talking about, if you warm it up for like three to ten minutes it will take MUCH longer to get rid of the water vapour. Doesn't hurt your engine... it's what it's designed to do. Warming up for 5 minutes is an old wives tale. or husbands. either way, it's lame and misguided.

best way to warm up your car in the morning and get rid of the water vapour is to nanna it until it reaches just under operating temperature (a safe temp is about 70-75°, suitable op temp being between 80° and 95°C).

Try it out, the lot of you. If there's one thing you can trust, it's a dude on the internet. (That dude is Doctor Karl, bitches.)

:D

Link to comment
https://www.sau.com.au/forums/topic/278906-r33-gts25t/#findComment-4713035
Share on other sites

while it is a bit off topic, i am also against the letting your car sit there and idle to warm up. the main reasons being that it takes longer for a car to warm up when it's just sitting there idling, which means the car is running for longer at colder temps. the other reason being that it doesn't warm up the oil in the gearbox or diff.

another thing to take into consideration is that if you run your car for 10 mins every morning before you start driving, over a 1yr period, that is nearly 61 hours of running that your engine has done that hasn't been taken into account on your odometer, which means more than likely not taken into account on your servicing frequency. and not to mention the extra fuel you are using.

Link to comment
https://www.sau.com.au/forums/topic/278906-r33-gts25t/#findComment-4713470
Share on other sites

30-60secs then I drive it. Stagea (being auto) I cruise along at 1500rpm while people behind me hurl abuse. Skyline I shifted at around 1000rpm (3L ftw :blink:) till it was out of cold start (>65deg).

Just don't load it up.

Edited by bubba
Link to comment
https://www.sau.com.au/forums/topic/278906-r33-gts25t/#findComment-4715420
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • These are small points I should actually add to my original post. GKtech makes an extended slave line for this conversion. It's what I use, and it works well. You'll also need a CD009 slave cylinder.  S/R Chassis Z33/Z34 Conversion braided clutch line As for transmission sensors, you'll need to both extend the wiring and replace the connectors. I can't recall which is which, but one is your neutral switch and the other the reverse switch. As they are just switches, just test for continuity with your transmission in neutral or reverse to figure out which is which. Connectors:  VQ35 neutral Switch Connector | Wiring Specialties VQ35 Reverse Switch Connector | Wiring Specialties 
    • I’ll try and see it could be the release bearing. As for the 4th gear grind maybe clutch doesn’t disengage properly cause it is slightly like very slightly hard to go into first could be due to the slab cylinder pin being short uni clutch is a twin plate.   Ive attached some assembly photos hopefully you can open the link and see maybe detect what’s wrong https://share.icloud.com/photos/0dc2YvW__Hl6jl-l2_0jejjpg https://share.icloud.com/photos/09e0jkWOK-vP48c1cfY6u3ViA https://share.icloud.com/photos/0b4rDmh5R7pK7fb1VtND73a3g https://share.icloud.com/photos/05eeUi_6dC4DVi80jOUYDgb0g https://share.icloud.com/photos/06335TgY1XxyIJal_wkdQLhzw
    • Yeah for sure that is peddle adjustment 
    • What are your thoughts on this after having it for a while, worth getting?
    • Downshifts are harder on transmissions than upshifts, the input shaft naturally slows down once disconnected from the engine so the synchros aren't doing all the work. There's no "natural" tendency for an input shaft to increase RPM. Something is not right there, I don't have a great answer on what. You can try a dedicated GL4 75W90, I plan to switch to Motorcraft XT-M5-QS which is supposedly a very good 75W90 for NB Miatas which have a weirdly sensitive transmission from the factory. I would chase down why your clutch is making a hissing noise, that's not normal. It might be no big deal but in the absence of anything else to investigate I would look at that.
×
×
  • Create New...