Jump to content
SAU Community

Recommended Posts

post-15295-1247447344_thumb.jpg

post-15295-1247447379_thumb.jpg

post-15295-1247447415_thumb.jpg

post-15295-1247447439_thumb.jpg

post-15295-1247447476_thumb.jpg

Hi all,

I am about to place an order with REX KELWAY on a set of high mount steampipe manifold for my RB engine and I want to see if anybody else is interested as well. Check out the photos, these are made of steampipe and CNC cut flanges. Beautifully presented and just as good, if not better than 6boost and Extreme.

RB20/25 high mount with/out external gate outlet - $890.

Other turbo / wastegate flange combinations available.

Let me know before the end of July '09 if interested. You can message me here or [email protected]

Thanks

Edited by smok74

Cool! Is this the advertising thread?

I've got a truckload of stuff I want to sell. Or can I piggy back off the headlight one?

Or should we pay the trader fee like the traders have to?

Cool! Is this the advertising thread?

I've got a truckload of stuff I want to sell. Or can I piggy back off the headlight one?

Or should we pay the trader fee like the traders have to?

As a matter of fact, Im not a trader, just someone that's come across some good things and wish to share it with my fellow Skyline owners at a good price.... I have email / correspondence between the suppliers and myself to prove this....But why should I have to justify myself to a nobody like you ?

By the way, these manifolds are from Kelway and the headlights are being developed by a company in NZ. You can try to get them individually and see if they'd do it for you at the bulk price. If these conditions dont qualify them as group-buys then I dont know what does

Edited by smok74
Guest
This topic is now closed to further replies.


  • Similar Content

  • Latest Posts

    • There are several aftermarket options available, from not-too-painful moneyhttps://justjap.com/collections/driveshafts-bearings/products/d-max-reinforced-replacement-rear-driveshaft-set-fits-nissan-s13-s14-s15-r32-r33-r34-c35 and  https://justjap.com/products/crank-motorsport-billet-rear-axles-fits-nissan-skyline-r33-gts-t-r34-gt-t?srsltid=AfmBOorQk4xkGUa98kO7v2ePLUiNt-HRrM2AwWNw9mbSIVE1ujBVwY__, all the way up to The Driveshaft Shop https://driveshaftshop.com/skyline-cv-axles/
    • Yeah based on old XRC5964S specs, it looks to be roughly GTX3576R sized? But this 5964S compressor will flow 90lb airflow somewhat similar to the compressors in both the GTX3584RS or G35-1050.. I fully expected the 0.64 rear A/R to choke up top - seems way too small from typical convention - but these are seemingly beneficial over the prior 0.82 results.. Be interesting to see if he comments on the EFR question in that thread - he mentioned in a prior video that BW EFR's were the "cats pajamas 10 years ago", but by the sounds of things all his kits have been using Xona for quite a while now.
    • Yeah it’s still got the oem manual gearbox and clutch, only kinda mods are a blow off valve, coil overs, and a aftermarket intercooler. Also had it for about 2 months now with a lovely midnight purple paint on it.
    • Yeeeppp, been following a lot of the testing on the latest Xona stuff and there are some mental results.  He also went over 1000hp @ 4 hubs on his Mainline with a XRE6364S (63mm) which was also well into the 20psi range before 4000rpm on a 2.5. Crazy stuff. Fwiw the XRE5964S is basically the modern equivalent of their old HTA3582 - would drive nicely enough on an RB25 or 26, but proven capable of a huge amount of power if you want to spicy with rpm tho even at sane boost levels will make stout numbers 
    • The axels in my R33 seem tired, and have a bit of play in them. I cannot find any new of course, not interested in buying used, but I am looking to see if anyone can identify some cross compatible axles. In the states I have seen suggested for S chassis the J30 axles, however for the skyline (as best I can tell) the lengths are about an inch off (2.5cm) on both sides. R33 my measure L 22" R 24.5" GPT L 22.5" 24.25" J30 L 23.5" 25.5"  so shaft length is probably an inch wider. Not sure if someone has another still remanufactured option besides the J30. I figured worst case I can buy a pair tear them down and swap the center shaft. My other option was reaching out to GSP to see if they cannot piece together a set, since the axle stubs are still manufactured, I wouldn't think it be that hard to find a shaft or make a shaft work. 
×
×
  • Create New...