Jump to content
SAU Community

Recommended Posts

Hi guys, I'm in a bit of a rush to get my car ready to leave for alot of work that will be completed in november. So I have finally gotten around to spending some time with the ratchet and getting off the parts that I want to sell.

What's remaining that I would like to get rid of today are ;

Genuine Ganador CF finish mirrors for r34 with the blue tinge lens.

$500 outright or $400 swap with standard mirrors.

Work S2R rims , good rubber all round, 18x9 , 18x10.5, good agressive offset, fill r34 guards, rears will need to be rolled. $1500 or $1200 with trade for any r34 5 stud stockies/na stockies that will fit.

Apexi AVC-R, good working order, $350

Signal CF bonnet with nose piece, $1200 or $900 swap over

Pair of Recaro Millenium with r34 rails, small rip on passenger seat from my belt, apart from that i'd give em a 7.5/10. $ 800!!!

The fabled TK dash, $750 or $550 with swap of standard cluster.

All pics of everything can be seen in my other threads.

All prices negotiable,

i'll be pulling this shit out all day so sms me on 0421 120 034.

Thanks ya'll.

Mods, if you'd be so kind to leave till around sun down, that'd be appreciated.

Located, inner east.

Link to comment
https://www.sau.com.au/forums/topic/279777-pulling-parts-of-my-car-today/
Share on other sites

Always intended on going Craft Square's so still not sure =/

eat the pudding eat the pudding eat the pudding eat the pudding eat the pudding eat the pudding eat the pudding

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • GTSBoy on your suggestion on another thread I had a look at those injectors and ended up getting them because of the quality.  Got the expensive ones.  
    • Hey guys been looking everywhere to try and find the correct gtr hood latch support part number but only found the first half and when I search with that number it sends me to an r34. The first part I found was 62515. If anyone could help me with the rest then I’d really appreciate it. Or if there’s some alternative hood latch support that would work even better cause I can’t find any for sale. (Searched on upgarage, partsouq,buyee,rhdjapan) 
    • If you've only done the upper control arms on the rear, AND you have changed their length (by more than about 1mm) to set the camber you want, then you will definitely need/want to install traction arms also. Adjusting the camber arms on their own WILL introduce bump steer and make the car unpleasant to drive. Most owners have no idea that their car could behave infinitely better than what they put up with. I'm not entirely sure what the Stageas need, but I am thinking that unless you have massive front spring rates and pretty soft rear springs, you have waaaay too much rear bar. Oversteer city, in my estimation. Combined with possible excessive bump steer from maladjusted arms, that could be a recipe for nastiness. ATR43SS2 is not a highflow. It is an outright replacement turbo. It's a little bit bigger than the largest highflow profile that Tao does. Probably a solid 300rwkW turbo where the bigger highflows will be about 30-40rwkW less. Nevertheless, we're only talking about ~300 rwkW, which is well within the abilities of the stock ECu to run with a Nistune on board. I would do so without hesitation - and I will be doing so when I get my finger out and actually get the injectors and AFM installed. But, if you would prefer to drop a whole lot more money on the ECU side, then I suspect you're looking at Haltech. The Haltech fanbois here will all spout on about all the available engine protection you can have, that you can't have with the Nistune option. And they're right. But it doesn't really come for free either. You will spend more money on extra sensors and the like, plus the work to install them. If the engine was built and therefore represented a big investment to protect, then I'd say definitely do it. If you view the current (and forever into the future) shortage of replacement engines as something to prompt similar protection, then also, do it. If you see a destroyed RB25 as an opportunity to put in a Mercedes or other V12 (like I kinda do)... then your perception of the risk/reward might differ. These are good injectors. You can also get a "better" set of the same with more flow matching, for more $$. 1000cc is where you will want to be. You will need an R35 AFM and adapter tube if you want to stay with Nistuned stock ECU. Otherwise, if going Haltech, you can ignore. As for intercooler. Just about anything will do. You're only talking about ~300rwkW. Just put a big core in there. Be aware that return flows do add significant pressure drop and will cost power and will make the turbo work harder to achieve the same goals. If you can manage a proper crossflow, do it. I'm keeping my very good return flow because I'm only expecting to be in the ~250rwkW range, and will live with whatever outcome I get.
    • I have a heap that i have collected if you want some authentic ones still. Pm me if your interested!
×
×
  • Create New...