Jump to content
SAU Community

1993 R33 Gtst


Recommended Posts

For Sale

-1993 S1 R33 GTST

-5 spd Manual

-RB25DET

-115xxx kms

- Rockhampton, Qld

Modifications

- 18 inch bronze DTM Z7

- UAS gtr style rear spoiler

- Exedy 5 puk ceramic button clutch

- Tein coilovers front & rear

- R33 Front seats

- Genuine Nissan floor mats

- Pioneer Head Unit

- Pioneer Speakers

- Aftermarket Alarm system

- 3 inch turbo back exhaust

- High flow cat

- Apexi pod

- Hybrid FMIC

- JJR coilpacks

- Turbosmart boost tee Boost Controller

- HKS turbo timer

General Info

-Car has been very well looked after and service regularly. The car is making a touch under 300hp on 11psi.

Price

$14000 NEG or

Swaps for something more track spec, 180sx, silvia, r32 plus cash my way or a cheap daily plus cash my way.

Will ship interstate at buyers expense.

If anyone has any questions about anything don’t hesitate to ask, pm or give me a call or sms on 0437 834 017 anytime after 5pm. Or swing me an email on [email protected].

post-43611-1248125869_thumb.jpg

post-43611-1248126690_thumb.jpg

post-43611-1248126786_thumb.jpg

post-43611-1248126824_thumb.jpg

post-43611-1248126845_thumb.jpg

post-43611-1248126889_thumb.jpg

post-43611-1248126920_thumb.jpg

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share



  • Similar Content

  • Latest Posts

    • Great info @tidi0x  Will definitely be handy for others and maybe me if I decide to keep the shit box H pattern.
    • Bumping this up one last time.... I wanted to follow up on the clutch slave issue. I realized that what the issue comes down to is the pocket is flat milled, and the cylinder does not want rest flat. So in order to mount it correctly you will need to make a spacer for the fingers so the cylinder is floating. I took two plates of aluminum, drilled some holes and was good. I did still need to make the relief cuts in the bell housing, as even with the spacer the bleed section still interferes. The OE bell housing the mounting holes are raised from the housing.       
    • If the event in USA goes ahead will be interesting as it seems the rules will get more cars over here. Apparently the track is laguna seca too. Yeah s15, if I get a the lower dash trims, centre console and change front cross member to standard LCA position will fit clubsprint. See how rules are as i would rather do complete widebody than a bolt on flare to run the 295 with proper clearance.
    • If the car is legal height I can't see it being an issue. Found a thread on reddit that might offer some insight.   I got a ticket from a copper in QLD for my S15 being too low. They had this wheel thing on a stick that they put under the car and it hit my exhaust. Anyhow went to an exhaust shop to get the exhaust tucked up/hung a little higher and I wound the coilovers up a smidge. Don't think I even had to go back to the police station unlike when I got defected for having a carbon bonnet when I brought the S15 from the ACT to QLD and had to replace it and then rock up at a police station and have a yougish female officer who knew nothing about cars confirm that I had changed bonnets. Should have just painted the carbon bonnet yellow to match the rest of the car lol
    • Id like to race in the US i think alot of those track would suit me   For the s15? Youd be stuck between club sprint and the new Open Am wouldnt you depending on how much interior you have left in
×
×
  • Create New...