Jump to content
SAU Community

Rb26 Block With Cradle Suit Re-bore To 86.5

sebastion
 Share

Recommended Posts

sebastion Proficient

sebastion

Posted
Posted

hey guys we have the following parts:

RB26 O5U block with some slight scoring of a few cylinders, needs a re-bore to 86.5mm, comes with cradle $400 (no squirters) pick-up

RB26 crankshaft, not sure if its from 32 or 33, how long is the oil drive between the two? $150 pick-up

RB26 conrods, great condition comes with pistons and pins (3 pistons great, 3 with pitting) $160 posted

RB26 polished intake plenum $500 or $300 exchange, need a standard one for testing pick-up

RB26 polished twin turbo pipe $150 no longer needed due to upgrade posted

R33 GTR v-spec turbos with actuators (no shaft play) $400 pick-up

RB26 injectors with fuel rail and reg (16,000 genuine k's) and resistor pack $450 posted

located near Lismore NSW, can deliver up as far as brisbane.

prices are reasonably firm, we are in no hurry to sell. pics will be up soon, for the plenum and pipe, see our other topic

cheers

sebastion Proficient

sebastion

Posted
  • Author
Posted

Pm replied.

also just realised the typo in our topic, the bare block is $500 not $400, still plenty of meat left in it, still has a 86mm bore.

  • 3 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      Rb26 iron block limit

      By GTSBoy · Posted

      Which is why I didn't mention that hardness testing, and specifically mentioned the bore and deck thickness testing. Yeah, not really. The bore temperature will be a lot more even around the top half inch or so, where the material distribution is dominated by the deck, and which is the only place where the bore surface temperature heating any gas in the cylinder is likely to have any effect on detonation. Think about it. Another inch or so down the bore, you might have a hotter spot. The gas there might get a bit hotter, then the piston rises squeezes that gas away from there at high speed and mixes it with other gas from nearby. Instant dilution of the problem. I'd be surprised if it was an issue at any time other than in racing engines or OEM dev engines being run at the ragged edge of tuning. Say what now?
    • joshuaho96
      Rb26 iron block limit

      By joshuaho96 · Posted

      https://dsportmag.com/the-tech/education/engine-tech-material-hardness-testing/ The PRP testing on block hardness I'm not sure how much it actually can be trusted. The thinner cylinder walls on RBs is a bit of a problem vs 2JZ but it really depends on the design goal. Siamesed cylinder bores like a 2JZ cause uneven cylinder wall temps too, which means a bit of distortion induced by that + the hotspot can affect knock margin. Something that actually gives me a bit of pause with the PRP block, whether super thick cylinder walls are going to keep it from being drop-in compatible on an otherwise OEM rebuild. 
    • Sleepergm
      Hks race car install

      By Sleepergm · Posted

      Yeah very valid point. I am waiting for one of the other tuners to come back from vacation so he can help me a bit when the cat is installed again. In the meantime I am going to finish up my polishing and ceramic coating that I have started myself.    N45 Dr Beasley product is highly recommended for a paint primer / polisher. Using this EXO Gtechniq also for the ceramic but next time might use the light serum before hand also. Looks great. 
    • joshuaho96
      Hks race car install

      By joshuaho96 · Posted

      Running rich in conditions where it shouldn't probably won't do great things for catalytic converter lifespan. I would fix that sooner than later.
    • GTSBoy
      Rb26 iron block limit

      By GTSBoy · Posted

      Yes, important point. Watch the Motive videos with Herman thickness testing the bores and deck. You do not want to push the unlucky (thin) block as hard as you can push the average block.
×
×
  • Create New...